Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Jointed Fishing Rods: Two- and Three-Piece Casting, Trout and Bass Fly, Salt-Water and Tarpon Rods (Boy Mechanic, 1915)
Woody

Створено

Woody

13. листопад 2026NO
7
0
0
0
0

Jointed Fishing Rods: Two- and Three-Piece Casting, Trout and Bass Fly, Salt-Water and Tarpon Rods (Boy Mechanic, 1915)

Part II of Stillman Taylor's rod-making series (The Boy Mechanic, Book 2, 1915): once the one-piece casting rod is mastered, the same planing, grasp and finishing methods make jointed rods. He gives full caliper tables and fitting lists for six rods; choose one in the notebook. Sections join with welted, shouldered ferrules, and every rod gets two tips "in view of a possible breakage".
Просунутий
About 2-3 weeks (glue and varnish drying)

Інструкції

1

His caliper tables

Завантаження блокнота Jupyter…
2

Read The Boy Mechanic, Book 2

"While the action of the one-piece rod is undeniably better than when the rod is made in two or three pieces, it is less compact to carry." He warns that "the more joints incorporated in a rod, the less satisfactory it will be from an angling standpoint", since ferrules cannot follow the rod's curve.
3

Choose the rod and get the stock

Pick a rod from the notebook. Stock (dagame or greenheart): two-piece casting -- butt 5/8 in x 3 ft, two tips 3/8 in x 3 ft; three-piece casting -- all 2 ft, butt 5/8 in, joint and tips 3/8 in; trout or bass fly -- butt 5/8 in x 4 ft, joint and tips 3/8 in x 4 ft; salt-water -- both 4 ft, butt 3/4 in, tip 1/2 in; tarpon -- one piece 1 in x 6-1/2 ft.

Матеріали для цього кроку:

Деревина дагамеДеревина дагаме4 штук

Необхідні інструменти ({count})

Ручна пилкаРучна пилка
РулеткаРулетка
4

Plane each section to its table

Plane, round and scrape each section exactly as for the one-piece rod, calipering at every station in the table. Two-piece casting rod: he first suggests a butt of about 23 in and a 32-1/2 in tip to fit a 35 in rod case, then specifies a 6-1/2 oz rod with a 32-1/2 in butt (15/32 in at the grasp to 19/64 in at the ferrule) and a 33 in tip (17/64 in to 7/64 in), equal when ferrule and top are on. Make two tips for each rod.

Матеріали для цього кроку:

Наждачний папірНаждачний папір1 штука

Необхідні інструменти ({count})

Ручний рубанокРучний рубанок
Обдирний стругОбдирний струг
Сталевий шкребокСталевий шкребок
Напилки (ручний напилок)Напилки (ручний напилок)
ШтангенциркульШтангенциркуль
5

Fit the ferrules

Fit a welted, shouldered ferrule at each joint, sized from his list: 17/64 in for the two-piece casting rod; 21/64 in and 15/64 in for the three-piece; 9/32 in and 11/64 in for the fly rods; 7/16 in for the salt-water rod; a 3/4 in male ferrule on the tarpon butt. The tip ferrule comes with two closed-end centres, one for each tip. Cement them on with ferrule cement; serrated (toothed) ferrule ends are wound with silk for strength.

Матеріали для цього кроку:

Металеве з'єднання колін вудлищаМеталеве з'єднання колін вудлища2 штук
Клей для втулокКлей для втулок1 штука
Шовк для обмотки вудлищШовк для обмотки вудлищ1 штука

Необхідні інструменти ({count})

Напилки (ручний напилок)Напилки (ручний напилок)
Пропановий пальникПропановий пальник
ШтангенциркульШтангенциркуль
6

Build the grasp and reel seat

Build the cork grasp and reel seat as for the one-piece rod: 3/4 in reel seat with straight hood for the casting rods (fly-rod type with butt cap on the fly rods, 9 in or 9-1/2 in of cork above it), 7/8 in on the salt-water rod with an 18 in double grasp, 1 in on the tarpon rod. Use a 1 in butt cap (1-1/8 in on the tarpon rod) and a taper (winding check) of the small-end size in his list. For an independent butt, fit the ferrule straight on a rounded dagame core so the seated ferrule does not touch the wood, cement and rivet it, fit a soft-pine sleeve over core and ferrule, glue it on, cement and rivet the reel seat, then glue on the corks and cut the core flush.

Матеріали для цього кроку:

Коркові кільцяКоркові кільця24 штук
Тваринний клейТваринний клей1 штука
Соснова дошкаСоснова дошка1 штука
КотушкотримачКотушкотримач1 штука
Затильник вудлищаЗатильник вудлища1 штука
Закінчення руків'я (віндинг-чек)Закінчення руків'я (віндинг-чек)1 штука
Клей для втулокКлей для втулок1 штука
Мідні заклепкиМідні заклепки1 штука

Необхідні інструменти ({count})

Макетний ніжМакетний ніж
Ручний дрильРучний дриль
Обдирний стругОбдирний струг
Пропановий пальникПропановий пальник
МолотокМолоток
7

Mount the guides and tops

Casting rods: two 1/2 in narrow agate guides, two No. 1 one-ring casting guides and two 3/32 in offset agate tops. Fly rods: two No. 4 snake guides on the butt joint, three No. 3 on the middle joint, three No. 2 on each tip, and two No. 7 agate angle fly tops of the wind-on kind. Salt-water rod: a 10/32 in stirrup-tube agate top and two No. 3 bell guides. Tarpon rod: two No. 11 wide raised agate guides, two No. 1 trumpet guides and a 3/8 in agate stirrup top; whip its guides on double, the first set 10 in from the top, the second 26 in from the reel. Whip with 00 silk (00 or 0 on the three-piece rod, size A on the salt-water and tarpon rods), using the invisible knot.

Матеріали для цього кроку:

Пропускне кільце вудлищаПропускне кільце вудлища8 штук
Тюльпан вудлищаТюльпан вудлища2 штук
Шовк для обмотки вудлищШовк для обмотки вудлищ1 штука
Бджолиний віскБджолиний віск1 штука

Необхідні інструменти ({count})

Напилки (ручний напилок)Напилки (ручний напилок)
Макетний ніжМакетний ніж
8

Shellac and varnish

Shellac the windings and varnish the rod with coach varnish as for the one-piece rod: thin coats, warm, three days between coats.

Матеріали для цього кроку:

Шелаковий лакШелаковий лак1 штука
Каретний лакКаретний лак3 штук

Необхідні інструменти ({count})

Широкий малярний пензельШирокий малярний пензель
9

Troubleshooting

Jointed rod troubleshooting.

Flow

Loading...
10

History and honest limits

From "Fishing-Rod Making and Angling, Part II" by Stillman Taylor, in **The Boy Mechanic, Book 2**, Popular Mechanics, 1915 (Project Gutenberg 44585; checked on the archive.org scan boymechanicbook200chic2, pp. 69-72). Two points are given as he wrote them: the two-piece casting rod's butt is about 23 in in one sentence and 32-1/2 in in the next; the three-piece rod's stock is "2 ft. long" while its finished sections are 21-1/2, 21-3/4 and 21 in. Guide counts in the list are for the fly rods, the largest set. The tools and metric figures are ours.

Матеріали

17

Необхідні інструменти

12

За цим кресленням виготовляють

Пов'язані креслення

Ці креслення діляться знаннями — техніки, матеріали або принципи

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...