Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Monorail Sled: Two Tandem Plank Runners Shod With Strap Iron, Steered Lying Down (Boy Mechanic, 1915)
Woody

Створено

Woody

13. листопад 2026NO
4
0
0
0
0

Monorail Sled: Two Tandem Plank Runners Shod With Strap Iron, Steered Lying Down (Boy Mechanic, 1915)

Harry Hardy's monorail sled from The Boy Mechanic, Book 2 (1915): two plank runners one behind the other under a 6 ft board, shod with square-edged strap iron that grips like a skate. The rider lies full length and steers the front runner with a bar, balancing like a cyclist.
Середній
About 1 day

Інструкції

1

His sketch in centimetres

Завантаження блокнота Jupyter…
2

Read The Boy Mechanic, Book 2

"Round iron or half-round iron should not be used, as these are liable to skid. The square, sharp edges of the strap iron prevent this and grip the surface just as a skate."
3

Cut and shoe the runners

Cut the two runners from 1 in plank to the size and shape of his sketch: the front runner 2 ft long, the rear one 2-1/2 ft long and about 1 ft high (the sketch prints the rear length with an inch mark; it is drawn as 2-1/2 ft). Shoe them with strap iron 1 in wide and 1/4 in thick, keeping the edges square and sharp.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини1 штука
Смуга з маловуглецевої сталіСмуга з маловуглецевої сталі1 штука
Шурупи по деревуШурупи по дереву1 штука

Необхідні інструменти ({count})

Ручна пилкаРучна пилка
Лобзикова пилкаЛобзикова пилка
Ножівка по металуНожівка по металу
Слюсарні лещатаСлюсарні лещата
Ручний дрильРучний дриль
ОлівецьОлівець
РулеткаРулетка
4

Fit the rear runner

Nail or bolt blocks on either side of the upper edge of the rear runner and screw the top board (6 ft long, 1 in thick) to them. Brace the runner with strap iron, as in the sketch.

Матеріали для цього кроку:

Соснова дошкаСоснова дошка1 штука
Дошка з твердої деревиниДошка з твердої деревини1 штука
Смуга з маловуглецевої сталіСмуга з маловуглецевої сталі1 штука
Болт із півкруглою головкоюБолт із півкруглою головкою1 штука
Шурупи по деревуШурупи по дереву1 штука

Необхідні інструменти ({count})

Ручна пилкаРучна пилка
Ножівка по металуНожівка по металу
Ручний дрильРучний дриль
МолотокМолоток
5

Fit the front runner and steering

Fit the front runner the same way, but with only one pair of blocks at the centre and a thin piece of wood on their tops as the fifth wheel. Bore the hole for the steering post 6 in from the front end of the top, a little larger than the post. Round the post where it passes through the hole and leave its upper end square, to take the steering bar tightly.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини1 штука
Смуга з маловуглецевої сталіСмуга з маловуглецевої сталі1 штука
Шурупи по деревуШурупи по дереву1 штука

Необхідні інструменти ({count})

Ручна пилкаРучна пилка
Коловорот із перкоюКоловорот із перкою
СтамескиСтамески
Ручний рубанокРучний рубанок
6

Troubleshooting

Monorail sled troubleshooting.

Flow

Loading...
7

History and honest limits

From "How to Make a Monorail Sled" by Harry Hardy, in **The Boy Mechanic, Book 2**, Popular Mechanics, 1915 (Project Gutenberg 44585; checked on the archive.org scan boymechanicbook200chic2, p. 50). The rear runner length is printed 2-1/2 with an inch mark but drawn longer than the 2 ft front runner, so it is read here as 2-1/2 ft. He gives no sizes for the blocks, braces or steering bar. The tools and metric figures are ours.

Матеріали

5

Необхідні інструменти

11

За цим кресленням виготовляють

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...