Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
DC Power Supply: SCR-Regulated, Voltage and Current Bridges with Automatic Cross-Over (Kupferberg & Ash, Forbro, US 3,305,763, 1967)
Ed

Створено

Ed

3. листопад 2026FI
8
0
0
0
0

DC Power Supply: SCR-Regulated, Voltage and Current Bridges with Automatic Cross-Over (Kupferberg & Ash, Forbro, US 3,305,763, 1967)

A variable DC supply regulated by controlled rectifiers instead of a series transistor. Two of the four rectifiers in the bridge are silicon controlled rectifiers; how late in each half-cycle they are fired sets the output. A voltage bridge and a current bridge each make an error signal, an analog OR gate passes whichever is larger, and the supply crosses over automatically between holding the voltage and holding the current. Result: a variable voltage / current regulated DC supply with automatic cross-over. Source: K. Kupferberg and J. Ash (Forbro Design), US 3,305,763 (1967), Fig. 1. Unknown: component values and the firing-angle circuit. Picture: the patent drawing.
Просунутий
Unknown

Інструкції

1

Build the controlled rectifier bridge

In a case, wire the cord through a switch and fuse to a transformer. Feed its secondary into a bridge of two ordinary rectifiers and two silicon controlled rectifiers. Smooth the negative output through a choke and a capacitor, then through a current-sensing resistor (with a second capacitor forming a further filter) to the negative output terminal; the positive goes straight to the positive terminal. Ours: the case, switch and fuse. Not given: the ratings.

Матеріали для цього кроку:

Алюмінієвий корпусАлюмінієвий корпус1 штука
Гнучкий шнур із вилкоюГнучкий шнур із вилкою1 штука
ТумблерТумблер1 штука
Плавкий запобіжникПлавкий запобіжник1 штука
Знижувальний трансформаторЗнижувальний трансформатор1 штука
ДіодДіод2 штук
Тиристор (SCR)Тиристор (SCR)2 штук
Згладжувальний дросельЗгладжувальний дросель1 штука
Електролітичний конденсаторЕлектролітичний конденсатор2 штук
Клема-барашокКлема-барашок2 output + and -

Необхідні інструменти ({count})

Ручний дрильРучний дриль
Набір викрутокНабір викруток
2

Build the two bridges

Current bridge: the sensing resistor, a reference Zener, a fixed resistor and the variable current-control resistor. Voltage bridge: the load across the output, the variable voltage-control resistor, a fixed resistor and a second reference Zener. Feed both Zeners from a small separate supply. Not given: the values, the Zener supply.

Матеріали для цього кроку:

СтабілітронСтабілітрон2 штук
РеостатРеостат2 voltage and current controls
ОпірОпір1 sensing and bridge resistors

Необхідні інструменти ({count})

ПаяльникПаяльник
3

Build the control chain and use it

Invert the current bridge's error in a phase-reversing amplifier and feed it, with the voltage bridge's error, to an analog OR gate that passes the larger. Amplify the result and feed it to a firing-angle control circuit that fires the two controlled rectifiers' gates later or earlier in each half-cycle. In use, set the voltage and the current: for any load larger than the cross-over resistance (voltage setting divided by current setting) the supply holds the voltage, for a smaller one the current. Not given: the amplifier, OR-gate and firing circuits in this form.

Матеріали для цього кроку:

Друкована платаДрукована плата1 штука
Набір транзисторівНабір транзисторів1 amplifiers
Невідомий матеріалНевідомий матеріал1 OR gate and firing-angle circuit
Дріт припоюДріт припою1 as needed

Необхідні інструменти ({count})

ПаяльникПаяльник

Матеріали

17

Необхідні інструменти

3

Пов'язані креслення

Ці креслення діляться знаннями — техніки, матеріали або принципи

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...