Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Rolling-Rocker Churn: A Box on Pegged Rockers Rolls Along Notched Ways So Its Fulcrum Follows the Cream
Buttercup

Створено

Buttercup

11. листопад 2026IE
5
0
0
0
0

Rolling-Rocker Churn: A Box on Pegged Rockers Rolls Along Notched Ways So Its Fulcrum Follows the Cream

Daniel Deshon 2d of Somerset, Pennsylvania, received US 27,701, dated 3 April 1860, for a churn. A box of cream stands on curved rockers whose pegs sit in notches along the ways of a stand. Rocked by a handle, the box tips end to end and the cream runs through racks of rods; as the rockers roll, the point they rest on moves along with the weight, so little force is needed. The patent gives no sizes; every size here is ours, and so is our reading of where the racks sit.
Середній
About 2 days

Інструкції

1

A fulcrum that walks

Завантаження блокнота Jupyter…
2

Cream rushing end to end through pins, one month before

Newbrough's barrel tips on a fixed pivot. Deshon's box rolls, so its pivot follows the cream.
3

Read US 27,701

"... this is done without contending but very little with the weight from the fact that the fulcrum at the bottom of the rockers (b) changes from one end to the other in accordance to the change of the weight inside of the vessel, always keeping in the center of the weight; consequently balancing the weight in its motion and saving most of the labor required to churn."
4

Vessel a and lid d

From 20 mm hardwood board make a box 600 x 250 mm inside and 290 deep; glue and screw it and seal the inside joints with silicone sealant. Cut a 150 mm opening across the middle of the top and a lid to fit it, with a hardwood block handle e.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини3 штук
Столярний клейСтолярний клей1 штука
Шурупи по деревуШурупи по дереву40 штук
Силіконовий герметикСиліконовий герметик1 штука

Необхідні інструменти ({count})

Циркулярний верстатЦиркулярний верстат
ЕлектролобзикЕлектролобзик
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Струбцина з напрямноюСтрубцина з напрямною
Набір викрутокНабір викруток
РулеткаРулетка
5

Racks i

Make two racks, each two hardwood side bars 24 x 20 mm, 355 long, with nine 10 mm stainless rods across between them. Stand them in the vessel leaning together, their feet on the floor 30 mm from the ends, meeting in the middle 240 mm above the floor.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини1 штука
Пруток із нержавкої сталіПруток із нержавкої сталі2 штук
Столярний клейСтолярний клей1 штука

Необхідні інструменти ({count})

Циркулярний верстатЦиркулярний верстат
Ножівка по металуНожівка по металу
Напилки (ручний напилок)Напилки (ручний напилок)
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
6

Rockers b with projections f, and handle c

Draw an arc of 400 mm radius with the compass on two 20 mm hardwood boards and cut each rocker with that arc as its bottom, 48 degrees of arc (325 mm), rising to the box's top; leave one 140 mm taller and cut a hand-hole in it as the handle c. Bore seven 12 mm holes along each arc, 6 degrees apart, and glue in dowel pegs standing 8 mm out as the projections f. Bolt a rocker on each long side of the vessel, centred, the arc's lowest point 40 mm below the vessel's bottom.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини2 штук
Шканти з твердої деревиниШканти з твердої деревини1 штука
Столярний клейСтолярний клей1 штука
Болт із півкруглою головкоюБолт із півкруглою головкою4 штук
Гайка-баранецьГайка-баранець4 штук

Необхідні інструменти ({count})

КомпасКомпас
ЕлектролобзикЕлектролобзик
ТранспортирТранспортир
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Набір перових сверделНабір перових свердел
Наждачний папірНаждачний папір
Розвідний ключРозвідний ключ
7

Pedestal h with ways and notches g

Cut two hardwood ways 520 x 120 x 30 mm and set them on edge under the rockers, 290 mm apart inside; join them with two cross boards near the floor. Cut seven notches 14 mm wide and 11 deep in each way's top edge, 41.9 mm apart from the middle, to match the pegs.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини2 штук
Столярний клейСтолярний клей1 штука
Шурупи по деревуШурупи по дереву16 штук

Необхідні інструменти ({count})

Циркулярний верстатЦиркулярний верстат
Набір стамесок по деревуНабір стамесок по дереву
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Струбцина з напрямноюСтрубцина з напрямною
Набір викрутокНабір викруток
РулеткаРулетка
8

The build in 3D

FreeCAD model of this build, tipped 10 degrees and cut through the middle: the vessel with its lid and the two racks leaning together, the rockers with their pegs in the ways' notches, and the pedestal.
Файл дизайнуBLENDCC0 - Free
9

Churn

Pour about 10 litres of heavy cream at about 15 °C, checked with the thermometer, into the vessel and close the lid. Push and pull the handle c steadily, tipping the vessel up to about 18 degrees each way, timing it. When the butter comes, lift the lid, take out the racks and the butter, tip the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Матеріали для цього кроку:

Жирні вершкиЖирні вершки10 l
Крупна морська сільКрупна морська сіль1 штука
ВодаВода1 штука

Необхідні інструменти ({count})

Термометр зі щупом, що лишається в стравіТермометр зі щупом, що лишається в страві
СекундомірСекундомір
Цифрові кухонні вагиЦифрові кухонні ваги
Велика миска з нержавкої сталіВелика миска з нержавкої сталі
10

Troubleshooting

Rolling-rocker churn troubleshooting.

Flow

Loading...
11

History and honest limits

**Daniel Deshon 2d** of Somerset, Pennsylvania, US 27,701, 3 April 1860, "Churn". He claimed the racks, vessel, pedestal and rockers with projections in notched ways, combined. He places the racks only by dotted lines in his figure; our two racks leaning together are our reading of them. Every size here is ours.

Матеріали

11

Необхідні інструменти

19

Файли дизайну

1

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...