Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Oblique-Slat Barrel Churn: Rows of Slats Inside a Turning Barrel Point Opposite Ways and Throw the Cream End to End
Buttercup

Створено

Buttercup

11. листопад 2026IE
4
0
0
0
0

Oblique-Slat Barrel Churn: Rows of Slats Inside a Turning Barrel Point Opposite Ways and Throw the Cream End to End

Pearson Embree of West Chester, Pennsylvania, received US 27,536, dated 20 March 1860, for a churn. Inside a common barrel churn turned by a crank, rows of wooden slats about a quarter of the diameter high point obliquely to the barrel's motion, each row the opposite way to the last. Some throw the cream toward one end, some toward the other; it strikes other slats or the projections on the heads and turns back. The slats' height follows the patent's proportion; every other size here is ours.
Середній
About 2 days

Інструкції

1

Slats a quarter of the diameter high

Завантаження блокнота Jupyter…
2

Cream thrown end to end, two weeks before

Newbrough rocks his barrel so the cream runs end to end through pins. Embree turns his, and oblique slats throw it.
3

Read US 27,536

"The slats A A A, etc., throw the cream toward an end of the churn (one portion of the slats throwing to one end and the remaining portion to the other end); as the cream is thrown violently toward the end it either strikes other slats, or the projections B B by either of which means its course is reversed and great agitation of the cream produced."
4

Barrel, heads and door

Cut 430 mm of food-grade PE pipe 315 mm across with a 12 mm wall. Cut two heads from 15 mm HDPE sheet to fit inside it and bore both 20 mm on the centre. Cut a door 200 x 120 mm in the pipe's side, between two rows of slats; keep the piece, screw two HDPE strips along its long edges so it rests on the pipe, and hold it with two hooks and eyes.

Матеріали для цього кроку:

Труба з поліетилену високої густиниТруба з поліетилену високої густини1 штука
Лист ПЕВГЛист ПЕВГ1 штука
Гачок і петляГачок і петля2 штук
Машинні гвинтиМашинні гвинти4 штук
Самоконтрувальна гайка з нейлоновим кільцемСамоконтрувальна гайка з нейлоновим кільцем4 штук

Необхідні інструменти ({count})

ЕлектролобзикЕлектролобзик
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Набір перових сверделНабір перових свердел
Напилки (ручний напилок)Напилки (ручний напилок)
Набір викрутокНабір викруток
РулеткаРулетка
5

Slats A, A', A'', A''' and projections B

Cut four hardwood strips 30 x 18 mm, 390 long, and sixteen hardwood slats 90 x 12 mm standing 73 mm from the barrel's wall, a quarter of its 291 mm inside diameter; round their ends if you like. Set four slats in each strip, 100 mm apart, each at 45 degrees to the strip: in the first and third strips one way, in the second and fourth the other. Screw the strips inside the barrel a quarter turn apart, through the wall with stainless screws and lock nuts, sealed with silicone, so each row points the opposite way from the row before. Screw two hardwood projections B, 20 x 90 mm and 30 deep, on each head's inner face, opposite each other, between the rows.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини1 штука
Столярний клейСтолярний клей1 штука
Машинні гвинтиМашинні гвинти16 штук
Самоконтрувальна гайка з нейлоновим кільцемСамоконтрувальна гайка з нейлоновим кільцем16 штук
Силіконовий герметикСиліконовий герметик1 штука
Шурупи по деревуШурупи по дереву8 штук

Необхідні інструменти ({count})

Циркулярний верстатЦиркулярний верстат
ТранспортирТранспортир
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Струбцина з напрямноюСтрубцина з напрямною
Наждачний папірНаждачний папір
Набір викрутокНабір викруток
Розвідний ключРозвідний ключ
6

Shaft, stand and crank

Pass a 20 mm stainless shaft 680 mm long through both heads, press the heads into the pipe's ends, screw them through the wall and seal the heads and the shaft's passages with silicone sealant. Make a hardwood stand: a base 600 x 400 mm and two uprights 40 x 120 mm, 30 mm beyond each end of the barrel, bored 20.8 mm 260 mm above the floor. Rest the shaft in them with collars, and fit a hardwood crank 130 mm long with a dowel handle on its long end.

Матеріали для цього кроку:

Пруток із нержавкої сталіПруток із нержавкої сталі1 штука
Силіконовий герметикСиліконовий герметик1 штука
Машинні гвинтиМашинні гвинти8 штук
Дошка з твердої деревиниДошка з твердої деревини2 штук
Столярний клейСтолярний клей1 штука
Шурупи по деревуШурупи по дереву8 штук
Shaft CollarShaft Collar2 штук
Шканти з твердої деревиниШканти з твердої деревини1 штука

Необхідні інструменти ({count})

Ножівка по металуНожівка по металу
Напилки (ручний напилок)Напилки (ручний напилок)
Циркулярний верстатЦиркулярний верстат
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Набір перових сверделНабір перових свердел
Набір викрутокНабір викруток
7

The build in 3D

FreeCAD model of this build, the barrel cut through the middle: four rows of oblique slats, alternate rows pointing opposite ways, the projections B on the heads, the door, the shaft, stand and crank.
Файл дизайнуBLENDCC0 - Free
8

Churn

Turn the door uppermost, pour in about 8 litres of heavy cream at about 15 °C, checked with the thermometer, and close it. Turn the crank steadily, timing it. When the butter comes, stop with the door uppermost, open it, tip the buttermilk out into a bowl, take out the butter, wash it in cold water until it runs clear, salt and weigh it.

Матеріали для цього кроку:

Жирні вершкиЖирні вершки8 l
Крупна морська сільКрупна морська сіль1 штука
ВодаВода1 штука

Необхідні інструменти ({count})

Термометр зі щупом, що лишається в стравіТермометр зі щупом, що лишається в страві
СекундомірСекундомір
Цифрові кухонні вагиЦифрові кухонні ваги
Велика миска з нержавкої сталіВелика миска з нержавкої сталі
9

Troubleshooting

Oblique-slat barrel churn troubleshooting.

Flow

Loading...
10

History and honest limits

**Pearson Embree** of West Chester, Chester County, Pennsylvania, US 27,536, 20 March 1860, "Churn". He claimed the slats or projections on the inner surface, each row pointing obliquely in the line of motion and the next row the opposite way. He says they make butter "in much less time than by the ordinary revolving churns". The slat height follows his quarter-diameter; the PE barrel, the 45-degree angle, the counts and all other sizes are ours.

Матеріали

15

Необхідні інструменти

17

Файли дизайну

1

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...