Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО

Digital Caliper: Capacitive Scale and Slider with Two-Chip Electronics (Baxter and Buehler, Starrett, 1986)
A six-inch caliper that reads out on a display. Under the slide, a strip of etched copper bars runs along the beam. Electrodes on the slider pass a signal through the bars by capacitance, and the slider's electronics count the bars crossed and work out the position in between.
Result: a digital caliper reading in inches or millimetres, repeatable to a ten-thousandth of an inch, with floating zero, peak hold and high/low limits. It runs on two 1.5 V cells at 10-50 microamps.
Source: L. K. Baxter and R. J. Buehler (L. S. Starrett Co.), US Patent 4,586,260 (1986). Unknown: the metal of the beam, slide and rod, their dimensions, the processor's program, and how the chips and display are made. Ours: the etchant, photoresist and glue. Picture: Wikimedia Commons.
Просунутий
2 days
Інструкції
1
1
Etch the scale
Etch the scale
Etch the scale pattern onto a strip of copper-clad epoxy fibreglass with photoresist and etchant. Each copper bar is 0.40 inch long, with a wider centre 0.12 inch long and two ends 0.14 inch long. Space the bars on 0.05 inch centres: the centres sit 0.004 inch apart, the ends 0.025 inch apart. Run the pattern the full length of the scale. Ours: dry film resist and ferric chloride.
Матеріали для цього кроку:
Заготовка друкованої плати (фольгована)1 strip, length of the beamНеобхідні інструменти ({count})
Сухий плівковий фоторезист
Розчин хлориду заліза(III)
Хімічно стійкі рукавички2
2
Fix the scale into the beam
Fix the scale into the beam
The beam is a metal bar with the fixed outside and inside jaws at one end, a wide shallow channel in its face and a second channel along its back. Fix the scale permanently into the face channel, copper up. The patent allows etching before or after this step. Not given: the metal, the dimensions and how the scale is fixed. Ours: epoxy.
Матеріали для цього кроку:
Штанга штангенциркуля1 with integral jaws
Двокомпонентна епоксидка1 a littleНеобхідні інструменти ({count})
Невідомі розміри3
3
Fit the parts to the circuit
Fit the parts to the circuit
The circuit is one folded piece: a double-sided slider board joined by a flexible hinge to a circuit board. Its bottom face has two pickup electrodes, 0.750 x 0.110 inch and 0.0625 inch apart. On each side of them is an interdigitated transmitter array: fingers 0.115 inch long on 0.025 inch spacing, opening to 0.0375 inch at the centre. On the circuit board, solder or wire-bond the two chips: an NEC uPD7503 3 V processor (768 bits RAM, 2 kB ROM) and a CMOS gate array. Then fit the LCD, the 100 kHz crystal, the integrating capacitor and the MODE and SET buttons. Not given: the processor's program. Ours: a capacitor from a kit.
Матеріали для цього кроку:
Гнучко-жорстка друкована плата1 slider board + circuit board
Інтегральна мікросхема2 uPD7503 CPU, CMOS gate array
Сегментний РК-індикатор1 5 digits
Кварцовий резонатор1 100 kHz
Набір конденсаторів1 one integrating capacitor
Кнопка2 MODE, SET
Дріт припою1 a littleНеобхідні інструменти ({count})
Паяльник4
4
Build the slide
Build the slide
The slide frame wraps the back and edges of the beam and carries the movable jaws. Fix it to the depth rod, which runs in the back channel of the beam; the rod's free end is the depth gauge. Put the moulded plastic housing between the frame ends. Fasten two metal wear strips under the slider board, one on each side of the scale. They ride on the beam and connect the board's copper to it. Not given: the metal and sizes.
Матеріали для цього кроку:
Рамка штангенциркуля1 with jaws
Невідомий метал1 depth rod and two wear strips
Корпус рамки1 штукаНеобхідні інструменти ({count})
Невідомі розміри
Набір точних викруток5
5
Assemble and check
Assemble and check
Fold the circuit into the housing recess, slider board facing the scale, and screw it to the frame. The electrodes must lie parallel to the scale bars at every point of travel. Put the two 1.5 V cells (the patent says 'zinc oxide') in the battery pockets of the circuit. The display shows five digits, a ten-thousandths bar graph, a minus sign and 'mm', plus PEAK, LOW, HIGH and LIMIT. Ours: check the reading against a vernier caliper.
Матеріали для цього кроку:
Машинні гвинти2 штук
Дисковий елемент живлення 1,5 В2 штукНеобхідні інструменти ({count})
Набір точних викруток
ШтангенциркульМатеріали
15- 1 strip, length of the beamЗаповнювач
- 1 with integral jawsЗаповнювач
- 1 a littleЗаповнювач
- 1 slider board + circuit boardЗаповнювач
- 2 uPD7503 CPU, CMOS gate arrayЗаповнювач
- 1 5 digitsЗаповнювач
- 1 100 kHzЗаповнювач
- 1 one integrating capacitorЗаповнювач
- Заповнювач
- 1 a littleЗаповнювач
- 1 with jawsЗаповнювач
- 1 depth rod and two wear stripsЗаповнювач
- 1 штукаЗаповнювач
- 2 штукЗаповнювач
- Заповнювач
Необхідні інструменти
7- Заповнювач
- Заповнювач
- Заповнювач
- Заповнювач
- 2 vendors sell this, none ship to you yetЗаповнювач
- Заповнювач
- Заповнювач
Матеріали з пов'язаних креслень
За цим кресленням виготовляють
Пов'язані креслення
Ці креслення діляться знаннями — техніки, матеріали або принципи
CC0 Суспільне надбання
Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.
Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.



