Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО

Digital Tachometer: Hand-Held Contact Type That Holds Its Reading (Sugiyama, Shimpo, US 4,000,465, 1976)
A hand-held digital tachometer. You press the contact head on its shaft against the end of a turning shaft and push the thumb button; a slotted disk inside chops a light beam into pulses, and the pulses counted in a fixed time, set by a quartz clock, appear in the window as the speed. A latch holds the reading after you take the tachometer away, so you can read it even where you could not see the window while measuring.
Result: a contact tachometer that shows revolutions per unit time and keeps the last reading.
Source: Y. Sugiyama (Shimpo Kogyo), US 4,000,465 (1976). Unknown: the number of holes, the clock, the gate time and the circuit details. Picture: the patent drawing.
Просунутий
Unknown
Інструкції
1
1
Make the housing and measuring shaft
Make the housing and measuring shaft
Make a cylindrical housing to hold in one hand, with a window in its side for the reading and a push button for the power switch where the thumb falls. Run a measuring shaft out of the front end in bearings and fit a contact head on its tip to press against the shaft being measured. Not given: materials, sizes. Ours: aluminium tube, a ball bearing.
Матеріали для цього кроку:
Алюмінієва трубка1 housing
Невідомий метал1 measuring shaft
Кульковий підшипник1 штука
Невідомий матеріал1 contact headНеобхідні інструменти ({count})
Токарний верстат по металу
Ручний дриль
Невідомі розміри2
2
Make the pulse generator
Make the pulse generator
Fix a disk on the measuring shaft with a ring of small holes evenly spaced near its edge. Put a light source on one side of the disk and a photodetector on the other: each hole passing makes one pulse. Shape and amplify the pulses. Not given: the number of holes. Ours: an LED and a photodiode.
Матеріали для цього кроку:
Невідомий матеріал1 slotted disk
Набір світлодіодів1 light source
Фотодіод (BPW34)1 photodetector
Опір1 набірНеобхідні інструменти ({count})
Ручний дриль3
3
Build the counting circuit
Build the counting circuit
Divide a quartz oscillator's clock down to gate pulses one unit of time long. Pass the measurement pulses through an AND gate during each gate pulse into a counter. At the start of each gate pulse a reset pulse clears the counter. After the gate pulse ends, the first measurement pulse that arrives triggers a latch pulse that loads the new count into the display. If the head has been taken off the shaft, no pulse arrives, no latch pulse is made, and the display keeps the last reading until the next measurement or until the power is switched off. Not given: the clock frequency and gate time. Ours: logic ICs and a seven-segment display.
Матеріали для цього кроку:
Друкована плата1 штука
Кварцовий резонатор1 штука
Набір логічних мікросхем1 divider, AND gate, counter, latch, reset
Драйвер семисегментного індикатора1 штука
Чотирирозрядний семисегментний індикатор1 штука
Дріт припою1 as neededНеобхідні інструменти ({count})
Паяльник4
4
Power it and measure
Power it and measure
Fit the battery and the thumb button as the power switch. Press the contact head against the end of the turning shaft so it turns with it, push the button, and read the revolutions in the window, now or after you take the tachometer away.
Матеріали для цього кроку:
Акумулятор1 штука
Кнопка1 штукаНеобхідні інструменти ({count})
ПаяльникМатеріали
15- 1 housingЗаповнювач
- 1 measuring shaftЗаповнювач
- Заповнювач
- 1 slotted diskЗаповнювач
- 1 light sourceЗаповнювач
- 1 photodetectorЗаповнювач
- 1 набірЗаповнювач
- 1 штукаЗаповнювач
- 1 штукаЗаповнювач
- 1 divider, AND gate, counter, latch, resetЗаповнювач
- Заповнювач
- Заповнювач
- 1 as neededЗаповнювач
- 1 штукаЗаповнювач
- Заповнювач
Матеріали з пов'язаних креслень
За цим кресленням виготовляють
CC0 Суспільне надбання
Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.
Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

