Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Trundle-and-Pitman Churn: One Crank Turns the Dasher Staff and Lifts It Up and Down at Once
Martin

Створено

Martin

9. листопад 2026NO
8
0
0
0
0

Trundle-and-Pitman Churn: One Crank Turns the Dasher Staff and Lifts It Up and Down at Once

Edward L. Dorsey of Greenwood, Indiana, received US 23,556, dated 12 April 1859, for giving a churn's dashers two motions at once. A crank turns a wheel with teeth on its face. The teeth work between the rounds of a trundle (lantern) wheel on the dasher staff and turn it, while a pin on the same wheel works a pitman that lifts and drops the staff. The staff carries a round dasher at its foot and an armed whipping dasher above; the up-and-down dasher keeps the cream from simply swirling round. This rung builds it in wood and steel rod on a square food container.
Середній
About 8 hours

Інструкції

1

Two motions from one crank

Завантаження блокнота Jupyter…
2

A crank that lifts the dasher, before it

Rarey's crank only lifted the dasher. Dorsey's turns it as well, from the same wheel.
3

Read US 23,556

"... the teeth of wheel H work between the rounds n, n, n, of trundle wheel C, and give a circular motion to the said dashers. Thus the staff and dashers have two distinct motions—a vertical reciprocating and a rotary motion."
4

Body A, top and upright B

Use a square food-grade container about 300 x 300 x 320 mm. Cut an 18 mm plywood top 340 mm square with a 24 mm hole in the middle for the staff, and screw two cleats underneath so it sits square on the rim. Screw a hardwood upright B 44 x 44 mm, 300 mm tall, to the top, its near face 110 mm from the hole, and bore it 12.5 mm square to the top, 260 mm above it.

Матеріали для цього кроку:

Посудина для зберігання харчової якостіПосудина для зберігання харчової якості1 штука
Лист фанериЛист фанери1 штука
Дошка з твердої деревиниДошка з твердої деревини1 штука
Шурупи по деревуШурупи по дереву10 штук
Столярний клейСтолярний клей1 штука

Необхідні інструменти ({count})

Ручна пилкаРучна пилка
ЕлектролобзикЕлектролобзик
Набір перових сверделНабір перових свердел
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Набір викрутокНабір викруток
РулеткаРулетка
5

Wheel H and shaft I

Cut an 18 mm plywood disc 300 mm across. Drill 36 holes 8 mm across, evenly round a 280 mm circle, and glue in 8 mm hardwood dowels standing 16 mm proud of the front face as the teeth. Drill an 8 mm hole 45 mm from the centre and press in an 8 mm steel pin 16 mm proud as pin o. Glue a hardwood hub 60 mm across on the back. Fix a 12 mm stainless rod through hub and disc with an M4 screw across as shaft I, pass it through the upright, and fix a hardwood crank D 132 mm long with a dowel handle on its far end.

Матеріали для цього кроку:

Лист фанериЛист фанери1 штука
Шканти з твердої деревиниШканти з твердої деревини1 штука
Столярний клейСтолярний клей1 штука
Пруток із нержавкої сталіПруток із нержавкої сталі1 штука
Дошка з твердої деревиниДошка з твердої деревини1 штука
Машинні гвинтиМашинні гвинти2 штук
Самоконтрувальна гайка з нейлоновим кільцемСамоконтрувальна гайка з нейлоновим кільцем2 штук

Необхідні інструменти ({count})

ЕлектролобзикЕлектролобзик
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Ножівка по металуНожівка по металу
Напилки (ручний напилок)Напилки (ручний напилок)
Наждачний папірНаждачний папір
Набір викрутокНабір викруток
6

Staff E, trundle C and dashers

Cut two hardwood heads M 74 mm across and 6 mm thick, bore each 20 mm in the middle and drill 8 holes 8 mm across on a 62 mm circle; glue in 8 dowel rounds n 116 mm long. Cut a 20 mm hardwood dowel 594 mm long as staff E and drill an 8.5 mm hole across it 14 mm below its top. Cut dasher J, an 18 mm plywood disc 200 mm across with six 28 mm holes, and dasher K, two plywood arms 230 x 24 mm halved into a cross. Glue J on the staff's foot, K 112 mm above it and the trundle where its middle meets the teeth with the staff halfway up its stroke.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини1 штука
Шканти з твердої деревиниШканти з твердої деревини1 штука
Лист фанериЛист фанери1 штука
Столярний клейСтолярний клей1 штука

Необхідні інструменти ({count})

Ручна пилкаРучна пилка
ЕлектролобзикЕлектролобзик
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Набір кільцевих пилокНабір кільцевих пилок
СтрубциниСтрубцини
Наждачний папірНаждачний папір
7

Pitman F

Bend an 8 mm stainless rod in the vise: a small eye at one end to go on pin o, then a straight length 80 mm from the eye's centre to a right-angle bend, then a leg 56 mm long that goes across through the hole in the staff's top as the pivot. Put the staff in through the top, set the eye on pin o with a washer and lock nut, and push the leg through the staff.

Матеріали для цього кроку:

Пруток із нержавкої сталіПруток із нержавкої сталі1 штука
Плоска шайбаПлоска шайба1 штука
Самоконтрувальна гайка з нейлоновим кільцемСамоконтрувальна гайка з нейлоновим кільцем1 штука

Необхідні інструменти ({count})

Слюсарні лещатаСлюсарні лещата
Ножівка по металуНожівка по металу
Напилки (ручний напилок)Напилки (ручний напилок)
Розвідний ключРозвідний ключ
8

The build in 3D

FreeCAD model of this build, the near half of the container cut away: the top and upright, wheel H with its dowel teeth and pin o, shaft I and crank D, the pitman bent into the staff's top, trundle C, and dashers K and J. It was checked for clashes at 12 crank positions through a full turn.
Файл дизайнуBLENDCC0 - Free
9

Churn

Lift the top, pour in about 12 litres of heavy cream at about 15 °C, checked with the thermometer, and set the top back. Turn the crank steadily and time it: the dashers turn and rise and fall together. When the butter comes, lift the top and staff out, pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

Матеріали для цього кроку:

Жирні вершкиЖирні вершки12 l
Крупна морська сільКрупна морська сіль1 штука
ВодаВода1 штука

Необхідні інструменти ({count})

Термометр зі щупом, що лишається в стравіТермометр зі щупом, що лишається в страві
СекундомірСекундомір
Цифрові кухонні вагиЦифрові кухонні ваги
Велика миска з нержавкої сталіВелика миска з нержавкої сталі
10

Troubleshooting

Trundle-and-pitman churn troubleshooting.

Flow

Loading...
11

History and honest limits

**Edward L. Dorsey** of Greenwood, Johnson County, Indiana, US 23,556, 12 April 1859, "Churn". He found it best in a square box, the rising and falling lower dasher checking the swirl the upper one gives. He claimed the trundle wheel, staff, pitman and cog wheel together. He gave no sizes or materials: every size and material here is ours.

Матеріали

13

Необхідні інструменти

18

Файли дизайну

1

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...