Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Fuller, Pritchel and Hot Setts: Steel Welded into a Split Iron Bar, with Twisted Rod or Withy Handles (Edwinson, 1886)
Forge

Створено

Forge

14. листопад 2026NO
6
0
0
0
0

Fuller, Pritchel and Hot Setts: Steel Welded into a Split Iron Bar, with Twisted Rod or Withy Handles (Edwinson, 1886)

The smith's own top and bottom tools, from George Edwinson's farrier's chapter in Amateur Work (1886): an inch iron bar upset, split into a fork and a steel wedge welded in, then forged into a fuller, pritchel punch, curved or straight hot sett, or a square-tanged bottom sett; the pritchel itself from 1/2 in. square tool steel; handles of twisted iron rod or green withy.
Просунутий
A day at the forge for the set

Інструкції

1

His proportions

Завантаження блокнота Jupyter…
2

Read Edwinson

"To make this tool, heat and upset the end of an inch bar of iron; then heat again and split with a sett."
3

Split the iron

Heat and upset the end of a 1 in. (25 mm) iron bar. Heat again and split it with a hot set into a fork 1 to 1 1/4 in. long by 3/4 in. wide (his fig. 108).

Матеріали для цього кроку:

Пруток кованого залізаПруток кованого заліза1 штука

Необхідні інструменти ({count})

Кувальне горноКувальне горно
КовадлоКовадло
КувалдаКувалда
Гаряче зубило (ковальська рубка)Гаряче зубило (ковальська рубка)
Ковальські кліщіКовальські кліщі
4

Weld in the steel

Heat the end of a steel bar of similar size and forge a wedge to fit the fork (fig. 109). Bring both to a welding heat and weld them well together.

Матеріали для цього кроку:

Тигельна стальТигельна сталь1 штука
Порошок буриПорошок бури1 штука

Необхідні інструменти ({count})

Кувальне горноКувальне горно
КовадлоКовадло
КувалдаКувалда
Ковальські кліщіКовальські кліщі
5

Forge the fuller

Cut off 2 in. of steel and 3 in. of iron for the tool. Forge the steel, with the iron behind it, into the fuller's rounded blade (fig. 102). Make the neck while it is still on the bar, then cut it off leaving a piece of iron for the head.

Необхідні інструменти ({count})

Кувальне горноКувальне горно
КовадлоКовадло
МолотокМолоток
Гаряче зубило (ковальська рубка)Гаряче зубило (ковальська рубка)
6

Same blank, other tools

Pritchel punch: about 2 in. of iron and 1 in. of steel, shaped as fig. 103. Curved set: as the fuller but with a gouge-shaped blade (fig. 105). Top hot set: the same, with a chisel or wedge blade (fig. 106). Bottom set: a wedge of steel and iron, edge up, on a square tang that fits the anvil's square hole (fig. 107).

Матеріали для цього кроку:

Пруток кованого залізаПруток кованого заліза1 штука
Тигельна стальТигельна сталь1 штука
Порошок буриПорошок бури1 штука

Необхідні інструменти ({count})

Кувальне горноКувальне горно
КовадлоКовадло
МолотокМолоток
КувалдаКувалда
Ковальські кліщіКовальські кліщі
7

Forge the pritchel

Forge 1/2 in. (13 mm) square tool steel into the tapered pritchel (fig. 104), 6 in. (150 mm) long. It punches nail holes in hot iron, so it need not be hardened.

Матеріали для цього кроку:

Пруток інструментальної сталіПруток інструментальної сталі1 штука

Необхідні інструменти ({count})

Кувальне горноКувальне горно
КовадлоКовадло
МолотокМолоток
Ковальські кліщіКовальські кліщі
8

Fit the handles

Rod handle: twist 3/8 in. iron rod once round the neck and weld the two ends together (fig. 110). Withy handle: take a green or half-green hazel, willow, oak or withy rod about 3 ft long, twist the middle 8-9 in., wrap it once round the neck and bind the two ends with wire or a link (figs. 106, 111).

Матеріали для цього кроку:

Круглий пруток з маловуглецевої сталіКруглий пруток з маловуглецевої сталі1 штука
Вербові прути (гнучкі)Вербові прути (гнучкі)1 штука
Залізний дрітЗалізний дріт1 штука

Необхідні інструменти ({count})

Кувальне горноКувальне горно
КовадлоКовадло
МолотокМолоток
Ковальські кліщіКовальські кліщі
9

Harden the cutting tools (ours)

He gives no temper for these. Ours: harden and temper the set edges as for other hot-cutting tools, and cool them often in use.

Необхідні інструменти ({count})

Кувальне горноКувальне горно
Гартівна діжкаГартівна діжка
10

Troubleshooting

Top-tool troubleshooting.

Flow

Loading...
11

History and honest limits

From George Edwinson, "Smithing and Forging" VII, **Amateur Work, Illustrated**, vol. VI (1886-87), pp. 14-16 and figs. 101-111 (checked on the archive.org scan amateurworkillus06lond). He calls the top hot cutter a "sett"; we map it to the Hot Chisel head and the bottom sett to the Hot Cut Hardy head. Temper, metric figures and tools are ours.

Матеріали

7

Необхідні інструменти

7

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...