Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Steeled Picks: Common Pick, Pickaxe and Miner's Pick, Iron Eye with Steel Points Welded In (Edwinson, 1886)
Forge

Створено

Forge

14. листопад 2026NO
6
0
0
0
0

Steeled Picks: Common Pick, Pickaxe and Miner's Pick, Iron Eye with Steel Points Welded In (Edwinson, 1886)

How a village smith made picks in the 1880s, from George Edwinson's smithing series in Amateur Work: an iron head welded round its eye, the ends split hot and steel wedges welded in, then hardened and tempered. Variants: the common pick, the pickaxe with a steel-laid axe blade, and the miner's pick with a steel-faced hammer end.
Просунутий
A day at the forge

Інструкції

1

Read Edwinson

"The eye or hole for the shaft is formed by first shaping the two sides ... and then welding the two parts together."
2

Form the eye

Forge the two halves of the head with a hollow for the eye in each (his fig. 216), lay them together and weld them into one head round the eye (fig. 217).

Матеріали для цього кроку:

Пруток кованого залізаПруток кованого заліза1 штука

Необхідні інструменти ({count})

Кувальне горноКувальне горно
КовадлоКовадло
МолотокМолоток
Ковальські кліщіКовальські кліщі
Оправка для розширення отворуОправка для розширення отвору
3

Draw the ends

Forge the two ends down to the size you need: a pointed bill and a chisel bill for the common pick, an axe and a point for the pickaxe, a point and a hammer for the miner's pick. For the miner's pick leave the eye massive and oval, tapering from both sides as in a hammer.

Необхідні інструменти ({count})

Кувальне горноКувальне горно
КовадлоКовадло
МолотокМолоток
КувалдаКувалда
4

Steel the points

Split each bill end with a hot chisel (his hot sett, fig. 218), insert a wedge of steel in the cleft and weld it in under borax, then draw it out to shape. Do not heat cast steel above a cherry red.

Матеріали для цього кроку:

Тигельна стальТигельна сталь1 штука
Порошок буриПорошок бури1 штука

Необхідні інструменти ({count})

Кувальне горноКувальне горно
Гаряче зубило (ковальська рубка)Гаряче зубило (ковальська рубка)
КувалдаКувалда
КовадлоКовадло
Ковальські кліщіКовальські кліщі
5

Steel the axe or hammer end

Pickaxe: enclose a slice of shear steel between the folding leaves of iron at the axe end and forge them down together to form the axe. Miner's pick: face the hammer end with steel.

Матеріали для цього кроку:

Плита рафінованої (зварювальної) сталіПлита рафінованої (зварювальної) сталі1 штука
Порошок буриПорошок бури1 штука

Необхідні інструменти ({count})

Кувальне горноКувальне горно
КовадлоКовадло
МолотокМолоток
Ковальські кліщіКовальські кліщі
6

Harden and temper

Harden the points and temper them to a brown tint tending to straw at the very point. Temper the pickaxe blade purple where steel meets iron, running to straw at the edge.

Необхідні інструменти ({count})

Кувальне горноКувальне горно
Гартівна діжкаГартівна діжка
7

Handle it (ours)

He does not cover the handle. Ours: shape an ash handle to the eye, drive it in and wedge it.

Матеріали для цього кроку:

Заготовка з ясенаЗаготовка з ясена1 штука
Дерев'яні клиниДерев'яні клини1 штука

Необхідні інструменти ({count})

СкобельСкобель
МолотокМолоток
8

Troubleshooting

Pick troubleshooting.

Flow

Loading...
9

History and honest limits

From George Edwinson, "Smithing and Forging" (part X), **Amateur Work, Illustrated**, vol. VI (Ward, Lock & Co., 1886-87), pp. 211-214 (checked on the archive.org scan amateurworkillus06lond). He gives no dimensions or weights; the sizes, the handle and the tools listed are ours.

Матеріали

6

Необхідні інструменти

9

Пов'язані креслення

Ці креслення діляться знаннями — техніки, матеріали або принципи

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...