Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Top and Bottom Swages: Steel-Faced Iron Like a Fuller, Square Tang Below, Withy Handle Above, or Sprung Together (Edwinson, 1886)
Forge

Створено

Forge

14. листопад 2026NO
6
0
0
0
0

Top and Bottom Swages: Steel-Faced Iron Like a Fuller, Square Tang Below, Withy Handle Above, or Sprung Together (Edwinson, 1886)

Swages, the smith's top and bottom tools for bringing a weld back to round or square, from George Edwinson's smithing series in Amateur Work (1886): steel or steel-faced iron made like a fuller, the bottom tool tanged for the anvil's square hole, the top tool on a withy or iron-rod handle, or the pair coupled by a steel spring for single-handed work.
Просунутий
A day at the forge per pair

Інструкції

1

Read Edwinson

"They may be made of steel throughout, or of steel-faced iron. The method of making them is similar to that for making fullers and setts."
2

Weld the blanks

As for a fuller: upset an iron bar, split it into a fork with a hot set, weld in a forged steel wedge. Or use steel throughout.

Матеріали для цього кроку:

Пруток кованого залізаПруток кованого заліза1 штука
Тигельна стальТигельна сталь1 штука
Порошок буриПорошок бури1 штука

Необхідні інструменти ({count})

Кувальне горноКувальне горно
КовадлоКовадло
КувалдаКувалда
Гаряче зубило (ковальська рубка)Гаряче зубило (ковальська рубка)
Ковальські кліщіКовальські кліщі
3

Bottom swage

Forge the steel face into a block with a square tang that fits the square hole in the tail of the anvil, like a bottom set (his figs. 285-288).

Необхідні інструменти ({count})

Кувальне горноКувальне горно
КовадлоКовадло
МолотокМолоток
Ковальські кліщіКовальські кліщі
4

Top swage

Forge the matching top tool with a neck for its handle.

Необхідні інструменти ({count})

Кувальне горноКувальне горно
КовадлоКовадло
МолотокМолоток
Ковальські кліщіКовальські кліщі
5

Cut the grooves

Form the working groove in each face to the section you need: round, half-round, oval, diagonal, square or rectangular. Groove sizes are ours: match the bars you forge.

Необхідні інструменти ({count})

Кувальне горноКувальне горно
Фулер (прутик для канавок)Фулер (прутик для канавок)
КовадлоКовадло
Напилки (ручний напилок)Напилки (ручний напилок)
6

Handle or spring

Give the top tool a hazel-rod or iron-rod handle as for fullers and top sets. For single-handed work, couple the top and bottom tools with a steel spring (fig. 283).

Матеріали для цього кроку:

Ліщинові прути (зелені, гнучкі)Ліщинові прути (зелені, гнучкі)1 штука
Круглий пруток з маловуглецевої сталіКруглий пруток з маловуглецевої сталі1 штука
Залізний дрітЗалізний дріт1 штука
Смуга пружинної сталіСмуга пружинної сталі1 штука

Необхідні інструменти ({count})

Кувальне горноКувальне горно
КовадлоКовадло
МолотокМолоток
7

Grind and harden

Grind the faces level so they fit each other, then heat the whole tool and harden it (his note for hand-worked dies).

Необхідні інструменти ({count})

Точильний кругТочильний круг
Кувальне горноКувальне горно
Гартівна діжкаГартівна діжка
8

Use them

Work the weld at a red heat. Hold the bar and the top swage; the striker hits the top tool with a light sledge. Pass the bar to and fro, turning it for round. After each heat gauge the weld in the swage block or with callipers.

Необхідні інструменти ({count})

Кувальне горноКувальне горно
КувалдаКувалда
ШтангенциркульШтангенциркуль
9

Troubleshooting

Swage troubleshooting.

Flow

Loading...
10

History and honest limits

From George Edwinson, "Smithing and Forging" XI, **Amateur Work, Illustrated**, vol. VI (1886-87), pp. 259-260 and figs. 283-290 (checked on the archive.org scan amateurworkillus06lond). The forging steps follow his fuller method (pp. 14-16). Groove sizes, the spring stock and the tools are ours.

Матеріали

7

Необхідні інструменти

11

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...