Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Sprung-Blade Inclined-Dasher Churn: The Blades Close to Pass the Narrow Top and Spread to Fill the Wide Bottom
Woody

Створено

Woody

9. листопад 2026NO
9
0
0
0
0

Sprung-Blade Inclined-Dasher Churn: The Blades Close to Pass the Narrow Top and Spread to Fill the Wide Bottom

John U. Fiester of Winchester, Ohio, received US 22,945 in February 1859 for a churn with a slanting dasher in a tub wider at the bottom than the top, so it is hard to tip over. The dasher's two blades are held to the spindle by a yoke spring and guided by pins in the slots of a cross tie: they close to pass the narrow top and spread to fill the wide bottom. Holes let the cream through the blades, and square pockets cut part way in carry air down into it. This rung builds it in pine and hardwood with a crank.
Середній
About 8 hours, plus printing

Інструкції

1

Tub, fill and the blades' reach

Завантаження блокнота Jupyter…
2

Holed beaters, before it

The Robies' beaters pass the cream through holes. Fiester's blades also have pockets that carry air down.
3

Read US 22,945

"... the yoke spring E and slots (a) allow the dasher blades to be forced easily into the smaller opening in the top of the tub, and when in to expand and fill the larger space at the bottom."
4

Print the journal box e

The block with the seat for the spindle's point. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
Файл дизайнуSTLCC0 - Free
5

Print the yoke collar

The collar on the spindle that holds the yoke spring. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
Файл дизайнуSTLCC0 - Free
6

Tub A and lid B

From 18 mm pine cut a floor 460 x 336 mm, two ends 400 mm wide at the foot, 320 mm at the top and 400 mm tall, and two sloping sides 336 mm wide that join them. Glue and screw the ends and sides on the floor so the tub is 400 mm wide inside at the floor and 320 mm at the top, 300 mm front to back. Cut a lid 374 x 336 mm with a turned dowel knob. Drill a 42 mm hole through the right side where the spindle meets it, about 345 mm above the inside floor.

Матеріали для цього кроку:

Соснова дошкаСоснова дошка3 штук
Столярний клейСтолярний клей1 штука
Шурупи по деревуШурупи по дереву40 штук
Шканти з твердої деревиниШканти з твердої деревини1 штука

Необхідні інструменти ({count})

Ручна пилкаРучна пилка
ЕлектролобзикЕлектролобзик
Акумуляторний дрильАкумуляторний дриль
Набір кільцевих пилокНабір кільцевих пилок
СтрубциниСтрубцини
Транспортир / кутомірТранспортир / кутомір
Наждачний папірНаждачний папір
Набір викрутокНабір викруток
РулеткаРулетка
7

Spindle C and journal e

Cut a 40 mm hardwood dowel 641 mm long and whittle or plane one end to a point over 30 mm. Screw the journal box in the left corner of the floor, against the sloping side. Cut a half-lap notch 30 mm wide and 12 mm deep across the spindle 85 mm from its point for the cross tie.

Матеріали для цього кроку:

Філамент PETGФіламент PETG1 штука
Шканти з твердої деревиниШканти з твердої деревини1 штука
Шурупи по деревуШурупи по дереву4 штук

Необхідні інструменти ({count})

3D-принтер FDM3D-принтер FDM
Ручна пилкаРучна пилка
СтамескиСтамески
Напилки (ручний напилок)Напилки (ручний напилок)
Набір викрутокНабір викруток
8

Blades D, tie F and yoke E

Draw an oval 340 x 220 mm on 16 mm hardwood and cut it in two along its length, then take 4 mm off each straight edge so the halves clear the spindle. Drill four 20 mm holes f in each blade and chisel four 20 mm square pockets d, 8 mm deep with bevelled sides, facing the same way. Glue a 9 mm dowel pin b into each blade 31 mm from its straight edge, 30 mm from its lower end. Cut a hardwood cross tie F 190 x 30 x 16 mm with a 10 mm slot 30 mm long near each end, glue it into the spindle's notch, and drop the pins into its slots. Slide the collar onto the spindle above the blades and screw two spring steel strips 15 x 1.5 mm, 42 mm long, from the collar to each blade's top end.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини1 штука
Шканти з твердої деревиниШканти з твердої деревини1 штука
Столярний клейСтолярний клей1 штука
Смуга пружинної сталіСмуга пружинної сталі1 штука
Машинні гвинтиМашинні гвинти8 штук
Самоконтрувальна гайка з нейлоновим кільцемСамоконтрувальна гайка з нейлоновим кільцем8 штук

Необхідні інструменти ({count})

ЕлектролобзикЕлектролобзик
Акумуляторний дрильАкумуляторний дриль
Набір перових сверделНабір перових свердел
СтамескиСтамески
Ножівка по металуНожівка по металу
Напилки (ручний напилок)Напилки (ручний напилок)
Наждачний папірНаждачний папір
Набір викрутокНабір викруток
9

Fit the dasher and crank

Pass the spindle's top out through the hole in the right side, squeeze the blades together through the tub's top and let them spread, and seat the point in the journal box. Fix a hardwood crank arm 130 mm long on the spindle outside the tub with a screw across, and glue in a 24 mm dowel handle 100 mm long.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини1 штука
Шканти з твердої деревиниШканти з твердої деревини1 штука
Столярний клейСтолярний клей1 штука
Шурупи по деревуШурупи по дереву1 штука

Необхідні інструменти ({count})

Ручна пилкаРучна пилка
Акумуляторний дрильАкумуляторний дриль
Набір перових сверделНабір перових свердел
Набір викрутокНабір викруток
10

The build in 3D

FreeCAD model of this build, the near half of the tub cut away: the sloping tub, the journal box, the slanting spindle with its two holed blades, the cross tie with its slots and pins, the yoke collar and springs, and the crank outside.
Файл дизайнуBLENDCC0 - Free
11

Churn

Pour in about 12 litres of heavy cream at about 15 °C, checked with the thermometer, and put the lid on. Turn the crank steadily and time it: the blades dip in and out of the cream, the pockets carrying air down. When the butter comes, pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

Матеріали для цього кроку:

Жирні вершкиЖирні вершки12 l
Крупна морська сільКрупна морська сіль1 штука
ВодаВода1 штука

Необхідні інструменти ({count})

Термометр зі щупом, що лишається в стравіТермометр зі щупом, що лишається в страві
СекундомірСекундомір
Цифрові кухонні вагиЦифрові кухонні ваги
Велика миска з нержавкої сталіВелика миска з нержавкої сталі
12

Troubleshooting

Sprung-blade churn troubleshooting.

Flow

Loading...
13

History and honest limits

**John U. Fiester** of Winchester, Guernsey County, Ohio, US 22,945, "Churn": the drawing reads 15 February 1859, the text 25 February 1859. A tub wider at the top can be overset; his is wider at the bottom, and the sprung, guided blades still fill it. He claimed the adjustable dasher with its yoke spring, slotted cross tie and pins, holes and air pockets. He gave no sizes or materials: ours are a pine tub, hardwood dasher and steel springs.

Матеріали

12

Необхідні інструменти

18

Файли дизайну

3

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...