Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Sliding-Head Churn Drive: The Churn Rides on the Pulley Head and Stays in Line When the Belt Is Slacked
Martin

Створено

Martin

9. листопад 2026NO
8
0
0
0
0

Sliding-Head Churn Drive: The Churn Rides on the Pulley Head and Stays in Line When the Belt Is Slacked

Joseph Forsyth of Wheeling, Virginia, received US 22,022, dated 9 November 1858, for working a churn by power from a big belt wheel. The pulley head slides along a guide block to tighten or slack the belt, which starts or stops the churn. The churn stands on a carriage fixed to the head, so its shaft stays in line with the pulley's. A platform on four screws raises or lowers different churns to the pulley's height. This rung builds it full size with a hand-cranked wheel and a rope belt.
Середній
About 2 days

Інструкції

1

Speed, rope and slack

Завантаження блокнота Jupyter…
2

Churns worked by power, before it

Brush worked a dasher from a dog's tread-wheel. Forsyth turns a crank churn by a belt and stops it by slacking the belt.
3

Read US 22,022

"The nature of my invention consists, first, in combining the carriage D with the movable pulley head H H in such a manner that the said carriage will move with the head when it is required to stop or start the motion of the churn, thereby enabling me to keep the shafts of the pulley, and churn in line."
4

Wheel A and posts B

Cut a plywood disc 1160 mm across and two discs 1200 mm across from 18 mm plywood. Glue and screw a larger disc to each face of the smaller one: the gap between them is the rope groove C. Screw a 160 mm hub block on each side. Stand two 70 mm posts 730 mm tall on 900 mm sills, 150 mm apart, each with two braces. Bolt a flange bearing on each post's outer face, 700 mm up, and run a 30 mm shaft M through bearings, posts and wheel, cross-bolted to the hub.

Матеріали для цього кроку:

Лист фанериЛист фанери3 штук
Столярний клейСтолярний клей1 штука
Шуруп по дереву #8 x 1"Шуруп по дереву #8 x 1"60 штук
Хвойний брус 70x70 ммХвойний брус 70x70 мм4 штук
Шуруп по дереву № 10 x 3"Шуруп по дереву № 10 x 3"24 штук
Фланцевий підшипникФланцевий підшипник2 штук
Сталевий вал 30 ммСталевий вал 30 мм1 штука
Набір шестигранних болтів M10Набір шестигранних болтів M105 штук

Необхідні інструменти ({count})

ЕлектролобзикЕлектролобзик
Ручна пилкаРучна пилка
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Набір перових сверделНабір перових свердел
СтрубциниСтрубцини
Розвідний ключРозвідний ключ
Будівельний рівеньБудівельний рівень
РулеткаРулетка
5

Crank

How the wheel is turned is not given; ours has a crank. Bolt a hardwood arm 350 x 70 x 30 mm on shaft M outside one bearing and glue a 30 mm dowel 150 mm long into it 280 mm from the shaft as the handle.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини1 штука
Шканти з твердої деревиниШканти з твердої деревини1 штука
Столярний клейСтолярний клей1 штука
Набір шестигранних болтів M10Набір шестигранних болтів M101 штука

Необхідні інструменти ({count})

Ручна пилкаРучна пилка
Акумуляторний дрильАкумуляторний дриль
Набір перових сверделНабір перових свердел
Наждачний папірНаждачний папір
Розвідний ключРозвідний ключ
6

Guide block and pulley head

Screw a 900 mm guide block U of 70 mm timber to the floor in line with the wheel, 1300 mm from shaft M. Lay a 400 mm head block on it. Cut two frames H from 50 x 8 mm flat bar, 420 mm long, and bolt them to the head block's sides so their ends run down the guide block's sides. Bolt a flange bearing on each frame's outer face 400 mm up. Make the pulley O like the wheel: a 200 mm disc between two 240 mm rings. Fit it on a 30 mm shaft through the bearings.

Матеріали для цього кроку:

Хвойний брус 70x70 ммХвойний брус 70x70 мм2 штук
Шуруп по дереву № 10 x 3"Шуруп по дереву № 10 x 3"8 штук
Смуга з маловуглецевої сталіСмуга з маловуглецевої сталі2 штук
Набір шестигранних болтів M10Набір шестигранних болтів M104 штук
Фланцевий підшипникФланцевий підшипник2 штук
Сталевий вал 30 ммСталевий вал 30 мм1 штука
Лист фанериЛист фанери1 штука
Столярний клейСтолярний клей1 штука
Шуруп по дереву #8 x 1"Шуруп по дереву #8 x 1"12 штук

Необхідні інструменти ({count})

Ножівка по металуНожівка по металу
Напилки (ручний напилок)Напилки (ручний напилок)
Слюсарні лещатаСлюсарні лещата
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
ЕлектролобзикЕлектролобзик
Розвідний ключРозвідний ключ
7

Strap F and thumb screw E

Bend a 30 x 5 mm flat bar into a bridge over the head block, 80 mm from the frames, and screw its legs to the guide block's sides. Drill its top for an M8 rod, run a nut onto the rod under the strap, and lock a wing nut on top as the thumb screw. Turn it down to clamp the head block.

Матеріали для цього кроку:

Смуга з маловуглецевої сталіСмуга з маловуглецевої сталі1 штука
Шуруп по дереву #8 x 1"Шуруп по дереву #8 x 1"4 штук
Шпилька різьбоваШпилька різьбова1 штука
Шестигранна гайкаШестигранна гайка2 штук
Гайка-баранецьГайка-баранець1 штука

Необхідні інструменти ({count})

Слюсарні лещатаСлюсарні лещата
Ножівка по металуНожівка по металу
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
8

Carriage D and platform K

Bolt two 70 mm side bars, 865 mm long, to the head block's side, 330 mm apart, and join their far ends with a cross tie with a caster under its middle as the roller. Drill each bar twice for M12 rods (screws I), 360 mm apart; fix each rod with a nut above and below the bar. Run a nut down each rod, lay an 18 mm plywood platform 430 x 440 mm on them, and lock it with a second nut on top.

Матеріали для цього кроку:

Хвойний брус 70x70 ммХвойний брус 70x70 мм2 штук
Набір шестигранних болтів M10Набір шестигранних болтів M104 штук
Комплект поворотних роликівКомплект поворотних роликів1 штука
Шпилька різьбоваШпилька різьбова4 штук
Шестигранна гайкаШестигранна гайка16 штук
Плоска шайбаПлоска шайба8 штук
Лист фанериЛист фанери1 штука

Необхідні інструменти ({count})

Ручна пилкаРучна пилка
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Розвідний ключРозвідний ключ
Будівельний рівеньБудівельний рівень
9

Arm X and the rope belt

Bolt a 140 mm flat-bar arm X with a 20 mm slot to a collar on the pulley shaft's end. Stand a crank churn on the platform and raise or lower the platform's nuts until its crank shaft is level with the pulley shaft and its handle V sits in the slot. Splice 12 mm cotton rope into a loop about 5 m long round both grooves (see the notebook), with the head slid towards the wheel.

Матеріали для цього кроку:

Смуга з маловуглецевої сталіСмуга з маловуглецевої сталі1 штука
Набір шестигранних болтів M10Набір шестигранних болтів M101 штука
Самоконтрувальна гайка з нейлоновим кільцемСамоконтрувальна гайка з нейлоновим кільцем1 штука
Бавовняна линваБавовняна линва6 m

Необхідні інструменти ({count})

Ножівка по металуНожівка по металу
Напилки (ручний напилок)Напилки (ручний напилок)
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Розвідний ключРозвідний ключ
РулеткаРулетка
10

The build in 3D

FreeCAD model of this build: the wheel on its posts with the crank, the guide block, pulley head, strap and thumb screw, the carriage with its caster, platform K on its four screws, a stand-in churn and arm X. The rope is not drawn.
Файл дизайнуBLENDCC0 - Free
11

Churn

Pour about 10 litres of heavy cream at about 15 °C into the churn. Slide the head away from the wheel until the rope is tight and clamp it with the thumb screw. Turn the wheel steadily, about 10 times a minute, and time it. To stop, loosen the thumb screw and slide the head towards the wheel: the carriage and churn move with it. When the butter comes, pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

Матеріали для цього кроку:

Жирні вершкиЖирні вершки10 l
Крупна морська сільКрупна морська сіль1 штука
ВодаВода1 штука

Необхідні інструменти ({count})

МаслобійкаМаслобійка
Термометр зі щупом, що лишається в стравіТермометр зі щупом, що лишається в страві
СекундомірСекундомір
Цифрові кухонні вагиЦифрові кухонні ваги
Велика миска з нержавкої сталіВелика миска з нержавкої сталі
12

Troubleshooting

Churn drive troubleshooting.

Flow

Loading...
13

History and honest limits

**Joseph Forsyth** of Wheeling, Ohio County, Virginia (now West Virginia), US 22,022, 9 November 1858, "Operating Churns". He claimed the carriage D combined with the movable platform K. He gave no sizes, named only the "metallic" frames H, and did not say what turns wheel A or what the belt is: our hand crank, plywood wheel and pulley, cotton rope, timber, bearings, rods and caster are ours.

Матеріали

21

Необхідні інструменти

18

Файли дизайну

1

Пов'язані креслення

Ці креслення діляться знаннями — техніки, матеріали або принципи

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...