Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Pendulum Churn: A Treadle Swings the Hung Churn, Arms From the Base Plunge the Dasher and a Twisted Strip Turns It
Buttercup

Створено

Buttercup

11. листопад 2026IE
5
0
0
0
0

Pendulum Churn: A Treadle Swings the Hung Churn, Arms From the Base Plunge the Dasher and a Twisted Strip Turns It

W. B. Gordinier of Coudersport, Pennsylvania, received US 28,170, dated 8 May 1860, for a pendulum churn. The churn stands in a frame that hangs like a swing and is set swinging with a treadle and a cord over a pulley. Arms from the base hold the dash rod's cross head, so as the swing moves the dasher plunges up and down, while a twisted strip on the rod, working through a slotted bar, turns it back and forth. The patent gives no sizes; every size here is ours.
Просунутий
About 3 days

Інструкції

1

Why the dasher plunges as the churn swings

Завантаження блокнота Jupyter…
2

A spiral that turns a push into a spin, one week before

Ashley slides a nut on a spiral to spin his beater. Gordinier slides his twisted strip through a slot.
3

Read US 28,170

"From this description it will be seen that the mechanism for operating the churn gives to the parts a combined vibrating, reciprocating, and alternate rotary motion, which are obtained by simply moving the treadle L."
4

Base A, standards B and cross bar B'

From pine lumber 60 x 50 mm make a base 1600 x 660 mm with four cross pieces, one under the pivot. Stand two standards 60 x 60 mm at the middle of the long sides, 1350 mm tall, joined at the top by a cross bar B'. Bore them 25 mm across 1300 mm above the floor for a 24 mm stainless pivot shaft, with the pulley J loose on its middle.

Матеріали для цього кроку:

Сосновий пиломатеріалСосновий пиломатеріал4 штук
Шурупи по деревуШурупи по дереву40 штук
Столярний клейСтолярний клей1 штука
Пруток із нержавкої сталіПруток із нержавкої сталі1 штука
БлокБлок1 штука
Shaft CollarShaft Collar2 штук

Необхідні інструменти ({count})

Циркулярний верстатЦиркулярний верстат
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Набір перових сверделНабір перових свердел
Струбцина з напрямноюСтрубцина з напрямною
Набір викрутокНабір викруток
РулеткаРулетка
5

Swing frame C, cross bar H and churn box E

Hang two hardwood hangers 90 x 30 x 60 mm on the pivot shaft, 400 mm apart, and fix two 20 mm hardwood dowels upright under each, 60 mm apart centre to centre, reaching 1150 mm down to a hardwood bottom board 440 x 440 x 25 mm. Across the arms 400 mm below the pivot fix a hardwood bar H with a slot 28 x 7 mm in its middle. Screw a 20-litre bucket to the board and cut a 28 mm hole in its lid's centre.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини2 штук
Шканти з твердої деревиниШканти з твердої деревини4 штук
Столярний клейСтолярний клей1 штука
Шурупи по деревуШурупи по дереву16 штук
Відро на 20 літрівВідро на 20 літрів1 штука

Необхідні інструменти ({count})

Циркулярний верстатЦиркулярний верстат
ЕлектролобзикЕлектролобзик
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Набір перових сверделНабір перових свердел
Струбцина з напрямноюСтрубцина з напрямною
Набір викрутокНабір викруток
6

Cross head D, dash rod D', strip G and arms F

Cut a hardwood cross head 28 x 40 mm, 504 long, notched at each end to run between a pair of arm rods, with a hardwood roller 36 mm across on a pin at each end. Bore its middle 21 mm. Cut a 20 mm stainless dash rod, cut a groove round it and hold it in the cross head with two key collars in the groove, so it turns; fix a hardwood dasher, two crossed boards 220 x 60 x 16 mm with four 20 mm holes, 410 mm below the cross head. Twist a stainless strip 25 x 3 mm, 300 long, a quarter turn every 90 mm in the vise, fix it to the rod's top and pass it up through bar H's slot. Cut two mild steel flat bar arms F with holes 640 mm apart; bolt one end of each to a bracket on the base under the pivot, 60 mm up, and the other to the cross head's end.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини1 штука
Шканти з твердої деревиниШканти з твердої деревини1 штука
Пруток із нержавкої сталіПруток із нержавкої сталі1 штука
Shaft CollarShaft Collar2 штук
Лист нержавкої сталіЛист нержавкої сталі1 штука
Смуга з маловуглецевої сталіСмуга з маловуглецевої сталі2 штук
Болт із півкруглою головкоюБолт із півкруглою головкою4 штук
Самоконтрувальна гайка з нейлоновим кільцемСамоконтрувальна гайка з нейлоновим кільцем4 штук
Столярний клейСтолярний клей1 штука

Необхідні інструменти ({count})

Циркулярний верстатЦиркулярний верстат
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Набір перових сверделНабір перових свердел
Ножівка по металуНожівка по металу
Ножиці по металуНожиці по металу
Слюсарні лещатаСлюсарні лещата
Напилки (ручний напилок)Напилки (ручний напилок)
Розвідний ключРозвідний ключ
7

Treadle L and cord K

Hinge a hardwood treadle 600 x 240 x 25 mm to a block on the base beyond the churn. Tie a cord to each end of the cross head, bring both up to the pulley J, take them over it together and down to the treadle's far end.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини1 штука
Меблева карткова завісаМеблева карткова завіса2 штук
Шурупи по деревуШурупи по дереву8 штук
ШнурШнур1 штука

Необхідні інструменти ({count})

Циркулярний верстатЦиркулярний верстат
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Набір викрутокНабір викруток
8

The build in 3D

FreeCAD model of this build, swung 12 degrees: the base and standards, the swing frame with its bottom board and the bucket cut open, the cross head between the arm rods, the arms F from the base, the dash rod and dasher, the twisted strip through bar H, the pulley J on the pivot shaft, the cord and the treadle.
Файл дизайнуBLENDCC0 - Free
9

Churn

Pour about 10 litres of heavy cream at about 15 °C, checked with the thermometer, into the bucket and put on its lid. Work the treadle with your foot in time with the swing, timing it, so the churn swings up to about 20 degrees each way. When the butter comes, stop the swing, unbolt the arms F from the cross head and lift the dash rod out, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Матеріали для цього кроку:

Жирні вершкиЖирні вершки10 l
Крупна морська сільКрупна морська сіль1 штука
ВодаВода1 штука

Необхідні інструменти ({count})

Термометр зі щупом, що лишається в стравіТермометр зі щупом, що лишається в страві
СекундомірСекундомір
Цифрові кухонні вагиЦифрові кухонні ваги
Велика миска з нержавкої сталіВелика миска з нержавкої сталі
10

Troubleshooting

Pendulum churn troubleshooting.

Flow

Loading...
11

History and honest limits

**W. B. Gordinier** of Coudersport, Potter County, Pennsylvania, US 28,170, 8 May 1860, "Churn" (the drawing spells the name Gordnier). He claimed the swinging frame carrying the churn, with the arms F, spiral plate G, cord K, pulley J and treadle L. He does not explain how the arms make the dasher rise and fall; the working above is ours. Every size is ours.

Матеріали

18

Необхідні інструменти

17

Файли дизайну

1

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...