Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Forged Centre Punches and Pin Punches: Point Hardened in Brine, Temper Run to Straw from the Stock (Griswold, Amateur Work, 1904)
Forge

Створено

Forge

14. листопад 2026NO
4
0
0
0
0

Forged Centre Punches and Pin Punches: Point Hardened in Brine, Temper Run to Straw from the Stock (Griswold, Amateur Work, 1904)

Robert Gibson Griswold's first tool-making lesson in Amateur Work (Boston, 1904): four centre punches from heavy to fine and nine pin, drift, offset and riveting punches, forged from carbon tool steel, finished with file and emery, then the point alone dipped in brine and the temper let run down from the hot stock to straw yellow.
Середній
A day for the set

Інструкції

1

His sizes

Завантаження блокнота Jupyter…
2

Read Griswold

"The more work put into the steel at the working point the better will be its grade."
3

Forge the blanks

Forge carbon tool steel at no more than a bright red into the shapes of his fig. 2: a 3/8 in. chamfered head, a 2 1/2 in. body and a 1 1/2 in. taper. Heavy centre punch at least 5/8 in. across with a conical point about 3/8 in. at the base; lighter centre punches 3/8 and 1/4 in.; pin punches 1/2, 3/8 (square end), 5/16 and 1/4 in., plus parallel-ended, offset and round-ended ones.

Матеріали для цього кроку:

Пруток інструментальної сталіПруток інструментальної сталі1 штука

Необхідні інструменти ({count})

Кувальне горноКувальне горно
КовадлоКовадло
МолотокМолоток
Ковальські кліщіКовальські кліщі
4

Finish before hardening

Do all work except grinding the point now: file each punch to shape and finish it with emery cloth. Keep the striking head slightly rounded so it does not broom.

Матеріали для цього кроку:

Шкурка на тканинній основі (шмергельне полотно)Шкурка на тканинній основі (шмергельне полотно)1 штука

Необхідні інструменти ({count})

Напилки (ручний напилок)Напилки (ручний напилок)
5

Harden the point

Heat the point to a dull red and plunge only the point, about 1/2 in. (13 mm), into a brine bath.

Матеріали для цього кроку:

Насичений сольовий розчинНасичений сольовий розчин1 штука

Необхідні інструменти ({count})

Кувальне горноКувальне горно
Ковальські кліщіКовальські кліщі
ВідроВідро
6

Run the temper

When the point is black, rub a bright spot with emery cloth on a flat stick and watch the heat from the stock colour it. At straw yellow (460 F) plunge the whole punch in water and keep it moving. If the stock has too little heat, lay it over the furnace to draw the colour.

Матеріали для цього кроку:

ВодаВода1 штука
Шкурка на тканинній основі (шмергельне полотно)Шкурка на тканинній основі (шмергельне полотно)1 штука

Необхідні інструменти ({count})

ВідроВідро
Кувальне горноКувальне горно
7

Grind the points

Grind the points to shape after hardening without letting the edge turn blue; if it blues, grind back to hard metal.

Необхідні інструменти ({count})

Настільний точильний станокНастільний точильний станок
8

Troubleshooting

Punch troubleshooting.

Flow

Loading...
9

History and honest limits

From Robert Gibson Griswold, "Tool Making for Amateurs" I, **Amateur Work** (Boston), vol. III (1903-04), pp. 273-275 and fig. 2 (checked on the archive.org scan amateurwork03bostrich). Metric figures and tools are ours.

Матеріали

4

Необхідні інструменти

7

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...