Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
One-Screw Two-Part Shaft Collar: Hooked Ends Reach Round the Shaft So the Halves Cannot Open (Grundy, 1907)
Forge

Створено

Forge

13. листопад 2026NO
3
0
0
0
0

One-Screw Two-Part Shaft Collar: Hooked Ends Reach Round the Shaft So the Halves Cannot Open (Grundy, 1907)

John R. Grundy of Philadelphia received US 860,369, dated 16 July 1907, for a two-part collar held by a single screw, where earlier split collars needed two. The screw passes through one pair of ends, an overhang on one part lying over the other. At the opposite side a tongue on one part fits a recess in the other. Both of those ends reach round the shaft past the diameter under the screw. When the screw's point presses the shaft, they hook under it and cannot open. Each part goes onto the shaft from the side, so the shaft stays in its bearings. We cut the two parts from a turned brass ring with a piercing saw, from a full-size template. The patent gives no sizes; every size here is ours.
Просунутий
About 2 days

Інструкції

1

Why the hooks hold

Завантаження блокнота Jupyter…
2

Read US 860,369

"It is obvious that by using the single screw in place of a plurality of screws, as has hitherto been considered necessary, I am enabled to reduce the cost of the collar." "The parts of said collar are placed in position on the shaft by being moved toward it in radial planes."
3

Turn the ring

Grip 45 mm brass round bar in the 3-jaw chuck. Face it, turn it to 40 mm for 20 mm, centre-drill, drill through 15 mm and ream 16 mm. Part off 16 mm long and face the parted side.

Матеріали для цього кроку:

Латунний круглий прутокЛатунний круглий пруток1 штука

Необхідні інструменти ({count})

Токарний верстат по металуТокарний верстат по металу
Трикулачковий токарний патронТрикулачковий токарний патрон
Токарний різецьТокарний різець
Набір центрувальних сверделНабір центрувальних свердел
Набір сверделНабір свердел
РозверткаРозвертка
Відрізний різецьВідрізний різець
Цифровий штангенциркуль 6 дюймівЦифровий штангенциркуль 6 дюймів
Захисні окуляриЗахисні окуляри
4

Print the cutting template

Full-size A4 template: the end view of the ring with the outlines of parts B and B', and the bottom of the ring seen from below with the tongue b' and cheeks a'. Print at 100 %; its 50 mm bar must measure 50 mm.
Файл дизайнуPDFCC0 - Free
5

Cut the parts apart

Glue the end view on one end face of the ring, centred, and the strip on the outside at the bottom. Wax the blade. Top joint: hold the ring in soft jaws, face up, and saw with the blade along the axis: in from the outside 5 mm left of the line to 14 mm radius, round the 14 mm circle to the line, and down the line into the bore. Bottom joint: turn the ring over and saw with the blade across the wall, following the strip from one end face to the other: the cheeks a' 3 mm left of the line, the tongue b' 3 mm right of it. Go slowly at the corners; the two parts come apart.

Необхідні інструменти ({count})

Струменевий принтерСтруменевий принтер
КлейКлей
Слюсарні лещатаСлюсарні лещата
М'які губки для лещатМ'які губки для лещат
Ювелірний лобзикЮвелірний лобзик
Бджолиний віскБджолиний віск
6

Fit the joints and cut away the bores

File the saw marks off the joints until the tongue slides into its recess and the overhang lies on the other part, with the two parts round a 16 mm bar. File each part's bore out to 18 mm across over the 22 degrees next to the top joint on its own side, B' to the left of the line and B to the right, as the template shows. Try them on the bar: put B on from below right, then B' from below left, sliding it up under the overhang and the tongue into its recess. File until each goes on without forcing.

Необхідні інструменти ({count})

Круглий пруток з маловуглецевої сталіКруглий пруток з маловуглецевої сталі
Слюсарні лещатаСлюсарні лещата
М'які губки для лещатМ'які губки для лещат
Набір напилківНабір напилків
Набір надфілівНабір надфілів
Цифровий штангенциркуль 6 дюймівЦифровий штангенциркуль 6 дюймів
7

Drill and tap for the screw

With both parts on the bar, the overhang lying on B', clamp the bar in the machine vice so the dashed screw line on the template stands upright. Drill 4.2 mm through the overhang and through B' into the bore, and tap M5 through both with cutting oil. Take the parts off and deburr the bore.

Матеріали для цього кроку:

Мастильно-охолоджувальна оливаМастильно-охолоджувальна олива1 штука

Необхідні інструменти ({count})

Круглий пруток з маловуглецевої сталіКруглий пруток з маловуглецевої сталі
Свердлильний верстатСвердлильний верстат
Машинні лещатаМашинні лещата
Набір сверделНабір свердел
Набір мітчиків і плашокНабір мітчиків і плашок
Коловорот для мітчиківКоловорот для мітчиків
Знімач задирокЗнімач задирок
8

The collar in 3D

FreeCAD model, our sizes: parts B and B' on a 16 mm shaft, the overhang b and the M5 screw at the top, the tongue b' between the cheeks a' at the bottom, and the bores cut away beside the top joint.
Файл дизайнуSTLCC0 - Free
9

Fit it on the shaft

Run an M5 x 12 cup point set screw into the overhang until it just shows. Put B onto the shaft from the side where the collar is wanted, then B' from the other side, its top under the overhang and its tongue into the recess. Tighten the screw with the hex key: it pushes on the shaft and draws both bottom ends down against it. Try to slide and turn the collar; it must not move.

Матеріали для цього кроку:

Установчий гвинт із чашоподібним кінцемУстановчий гвинт із чашоподібним кінцем1 штука

Необхідні інструменти ({count})

Набір шестигранних ключівНабір шестигранних ключів
10

Troubleshooting

Grundy collar troubleshooting.

Flow

Loading...
11

History and honest limits

**John R. Grundy** of Philadelphia, US 860,369, dated 16 July 1907, filed 28 January 1907. He claimed "a shaft collar made in two parts, and means for holding the parts together comprising a single screw passing through two adjacent ends of said two parts, the other ends of said parts being formed to co-act with the shaft to prevent their separation". His screw end also has a second projection b2 in a recess, holding the parts in line along the shaft; ours leaves it out, as the screw through both parts does that. His screw has a hex head; ours is a socket set screw. He gives no material; ours is brass, which a piercing saw cuts well. The patent gives no sizes; every size here is ours.

Матеріали

3

Необхідні інструменти

24

Файли дизайну

2

За цим кресленням виготовляють

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...