Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Cart Crupper, Breeching, Belly-Band and Straps (Hasluck, Harness Making, 1904)
Tex

Створено

Tex

13. листопад 2026FO
5
0
0
0
0

Cart Crupper, Breeching, Belly-Band and Straps (Hasluck, Harness Making, 1904)

The rest of a cart harness, from Paul N. Hasluck's Harness Making (1904): the crupper that runs from the saddle under the tail, the breeching round the hindquarters with its tugs and loin straps, the belly-band, hame straps and a leading rein. All sizes are his. With the bridle, collar and cart saddle it completes the set.
Просунутий
About 3 days

Інструкції

1

Cutting list

Завантаження блокнота Jupyter…
2

Read Harness Making, ch. VII

"To make the breeching, cut the body, if possible, 7 ft. 4 in. long and about 4 in. wide. Turn it down to 4 ft. 10 in. long, the strong end less than the weak."
3

Cut the crupper body and dock

Cut the body 2 ft 6 in or 2 ft 8 in long and 3½ to 4 in wide; cut a semicircle in the centre from the weak end, leaving a point about ¾ in wide each side, and cut an 8 in piece to line this end. Cut a piece ⅞ in wide and 8½ in long, shave its ends, and stitch it edge to edge into a round to within 1½ in of each end, with a cord or strip of leather inside; rub it round, blacken it and flatten both ends with a hammer.

Матеріали для цього кроку:

Лимарна шкіраЛимарна шкіра1 штука
Конопляний шпагатКонопляний шпагат1 штука
Шкіряна ниткаШкіряна нитка1 штука
Фарба для шкіриФарба для шкіри1 штука

Необхідні інструменти ({count})

Ніж для шкіриНіж для шкіри
Дві лимарські голкиДві лимарські голки
ШилоШило
Молоток-цвяходерМолоток-цвяходер
4

Finish the crupper body

Point the square end, reducing it to about 2 in. Race it along the sides and ends, edge and black it, and run a hot iron over the creases. Prick it about nine per inch as far as the lining reaches from the semicircle. Put the ends of the round piece under the points, one each side, the lining under them, and stitch all round and across the points with three-cord black-wax thread; trim, black and rub the edges.

Матеріали для цього кроку:

Шкіряна ниткаШкіряна нитка1 штука
Фарба для шкіриФарба для шкіри1 штука

Необхідні інструменти ({count})

Ніж для шкіриНіж для шкіри
Лимарський циркуль-борозникЛимарський циркуль-борозник
КрайкорізКрайкоріз
Лимарський скошений гладильникЛимарський скошений гладильник
Пропановий пальникПропановий пальник
Пробійник для шкіри (пробійна вилка)Пробійник для шкіри (пробійна вилка)
ШилоШило
Дві лимарські голкиДві лимарські голки
Лимарські лещатаЛимарські лещата
5

Make the crupper lay

Cut the lay 1 in narrower than the body and 3 ft long; turn in 10 in at the strong end and beat it flat. Turn the other end down 2 in and cut it slanting to 1½ in for a buckle, with a buckle hole. Mark cross lines 2 in from the broad point, ¼ in from the end of the bend underneath, and 2½ in from that toward the buckle. Edge the top only, crease two lines and hot-iron them, with inner lines about ¼ in in. Leave two openings for the hip straps, one in the bend and one in the middle; black and prick the stitched parts. Fix the buckle, lay it on the centre of the body with the broad end reaching the edge of the semicircle, tack and stitch, spotting the three cross lines.

Матеріали для цього кроку:

Лимарна шкіраЛимарна шкіра1 штука
Залізна пряжка з язичкомЗалізна пряжка з язичком1 штука
Шкіряна ниткаШкіряна нитка1 штука
Фарба для шкіриФарба для шкіри1 штука

Необхідні інструменти ({count})

Ніж для шкіриНіж для шкіри
КрайкорізКрайкоріз
БігувальникБігувальник
Лимарський скошений гладильникЛимарський скошений гладильник
Пробійник для шкіриПробійник для шкіри
Пробійник для шкіри (пробійна вилка)Пробійник для шкіри (пробійна вилка)
ШилоШило
Дві лимарські голкиДві лимарські голки
6

Pad the crupper and fit its strap

Cut thick felt as wide as the body, from the point of the semicircle to 2 in beyond the cross line near the buckle; cover it with basil, coarse-stitch it along the centre, turn the ends over and fasten them, and stitch it in place next the body with four or five stitches here and there, well secured at each corner. Cut a hole through the body opposite the buckle, 1½ in wide. Make a strap 9 in long, pointed one end and shaved the other, crease, black and stitch its shaved end to the narrow end of the body; it goes round the saddle's dock and up through the hole to the buckle on the lay.

Матеріали для цього кроку:

Вовняна повстьВовняна повсть1 штука
Овеча шкіра (бейзил)Овеча шкіра (бейзил)1 штука
Лимарна шкіраЛимарна шкіра1 штука
Шкіряна ниткаШкіряна нитка1 штука
Фарба для шкіриФарба для шкіри1 штука

Необхідні інструменти ({count})

Ніж для шкіриНіж для шкіри
Пробійник для шкіриПробійник для шкіри
ШилоШило
Дві лимарські голкиДві лимарські голки
7

Make the breeching body

Cut the body 7 ft 4 in x about 4 in and turn it down to 4 ft 10 in, the strong end less than the weak; edge, black and crease two rows along the edges. Mark a cross line about 1½ in from the centre of the bend each side, and at each end. Line the bend with 1 ft pieces bent flesh outward, one end about 1 in shorter; prick, tack and stitch row to row to make the eye for the bridgeband pin. Trim, blacken and rub the bend with tallow and bone; beat it with a wooden mallet if hard, and stitch the double part along ends and sides.

Матеріали для цього кроку:

Лимарна шкіраЛимарна шкіра1 штука
Шкіряна ниткаШкіряна нитка1 штука
Фарба для шкіриФарба для шкіри1 штука
ЛійЛій1 штука

Необхідні інструменти ({count})

Ніж для шкіриНіж для шкіри
КрайкорізКрайкоріз
БігувальникБігувальник
Пробійник для шкіри (пробійна вилка)Пробійник для шкіри (пробійна вилка)
ШилоШило
Дві лимарські голкиДві лимарські голки
Кісточка для фальцюванняКісточка для фальцювання
Дерев'яний молоток (киянка)Дерев'яний молоток (киянка)
8

Put on the breeching lay

Cut the lay the same length and 1 in narrower; edge, crease and black it, run another line ¼ in inside the crease, prick the two inner lines nine to the inch and turn it down at both ends as the body. Tack it on the centre of the body, light end against heavy end, and stitch end to end to the cross lines, bulging the cross stitching inward about 1 in at the middle. Punch a large hole where the stitches bulge and cut straight out each side for the chain to catch the pin. Cut a slot for the 1½ in tug 1 ft 4 in from each end.

Матеріали для цього кроку:

Лимарна шкіраЛимарна шкіра1 штука
Шкіряна ниткаШкіряна нитка1 штука
Фарба для шкіриФарба для шкіри1 штука

Необхідні інструменти ({count})

Ніж для шкіриНіж для шкіри
КрайкорізКрайкоріз
БігувальникБігувальник
Пробійник для шкіри (пробійна вилка)Пробійник для шкіри (пробійна вилка)
Пробійник для шкіриПробійник для шкіри
ШилоШило
Дві лимарські голкиДві лимарські голки
9

Make the tugs and safes

Two hind tugs 1 ft 8 in long, 6 in turned down each end to meet; buckle hole in the weak end; black, crease, rub and prick them. Put the strong end up through the slot from underneath, joint in front under the loop, buckle on the other end; make a loop about 2½ in long round both thicknesses and pull it over the joint. Cut a safe for each from the breeching to an inch beyond the buckle and ½ in wider each side, narrowed and shaved at the bottom, rounded at the top with a loop; finish it on the 1½ in loop-stick, beat it flat and square, nail it from underneath with about five nails each side clinched on the loop-stick, and crease it again with a hot iron. Stitch the safes along the tugs. Make the front tugs for the bridgeband pins the same but shorter, so their length from the breeching equals the hind tugs; fit the pins with their nut and washer.

Матеріали для цього кроку:

Лимарна шкіраЛимарна шкіра1 штука
Залізна пряжка з язичкомЗалізна пряжка з язичком4 штук
Болт шлеїБолт шлеї2 штук
ЦвяхиЦвяхи1 штука
Шкіряна ниткаШкіряна нитка1 штука
Фарба для шкіриФарба для шкіри1 штука

Необхідні інструменти ({count})

Ніж для шкіриНіж для шкіри
Пробійник для шкіриПробійник для шкіри
Оправка для шльовокОправка для шльовок
Молоток-цвяходерМолоток-цвяходер
Лимарський скошений гладильникЛимарський скошений гладильник
Пропановий пальникПропановий пальник
БігувальникБігувальник
Пробійник для шкіри (пробійна вилка)Пробійник для шкіри (пробійна вилка)
ШилоШило
Дві лимарські голкиДві лимарські голки
Розвідний ключРозвідний ключ
10

Make the loin straps

Cut two loin straps 3 ft 8 in x 1½ in to fasten to the tugs and pass through the openings in the crupper; point each end, crease double each side, edge, black, hot-iron the creases and make six or seven holes in each end.

Матеріали для цього кроку:

Лимарна шкіраЛимарна шкіра1 штука
Фарба для шкіриФарба для шкіри1 штука

Необхідні інструменти ({count})

Ніж для шкіриНіж для шкіри
КрайкорізКрайкоріз
БігувальникБігувальник
Лимарський скошений гладильникЛимарський скошений гладильник
Пропановий пальникПропановий пальник
Пробійник для шкіриПробійник для шкіри
11

Make the leading rein and hame straps

Leading rein: a 1 in strap about 8 ft 6 in long in all, with a buckle and a billet 1 ft long at one end and a chain with a spring hook at the other; black and crease it and stitch on buckle, billet and chain. The chain goes through the near bit ring and hooks to the other ring; the billet fastens to the crupper. Hame straps: 1¼ in, about 1 ft 8 in long, buckle and loop at one end, the other pointed with holes.

Матеріали для цього кроку:

Лимарна шкіраЛимарна шкіра1 штука
Залізна пряжка з язичкомЗалізна пряжка з язичком3 штук
Залізний ланцюгЗалізний ланцюг1 штука
КарабінКарабін1 штука
Шкіряна ниткаШкіряна нитка1 штука
Фарба для шкіриФарба для шкіри1 штука

Необхідні інструменти ({count})

Ніж для шкіриНіж для шкіри
БігувальникБігувальник
Пробійник для шкіриПробійник для шкіри
ШилоШило
Дві лимарські голкиДві лимарські голки
12

Make the belly-band

Cut it 3 in wide and 3 ft 8 in long, narrowed to 2 in for 6 in at both ends, with a buckle hole about 3 in from the point. Make two billets 2 ft 2 in x 2 in and two loops about 1¾ in wide; edge, crease and black everything. Prick the billets six per inch for about 6 in from the shaved end, set the buckle with the billet lapping 3 in over it and the loop about 1 in from the buckle, tack and stitch with six-cord black-wax thread, twice waxed, with two or three stitches in the centre of each end. Open and crease the loops and make four holes in the billets.

Матеріали для цього кроку:

Лимарна шкіраЛимарна шкіра1 штука
Залізна пряжка з язичкомЗалізна пряжка з язичком2 штук
Шкіряна ниткаШкіряна нитка1 штука
Фарба для шкіриФарба для шкіри1 штука

Необхідні інструменти ({count})

Ніж для шкіриНіж для шкіри
КрайкорізКрайкоріз
БігувальникБігувальник
Пробійник для шкіри (пробійна вилка)Пробійник для шкіри (пробійна вилка)
Пробійник для шкіриПробійник для шкіри
ШилоШило
Дві лимарські голкиДві лимарські голки
Лимарські лещатаЛимарські лещата
13

Troubleshooting

Crupper and breeching troubleshooting.

Flow

Loading...
14

History and honest limits

From **Harness Making**, edited by Paul N. Hasluck, Cassell and Company, 1904, chapter VII, "Cart Saddles, Reins, etc." (Project Gutenberg #70169). All sizes are his. Not made here: the iron-dee crupper he gives as a matter of taste, the ornamental breast-plate, the maker's-name stamp, and the final coat of "Harris's liquid or composition", a trade dressing. The heat source for the iron and the metric figures are ours.

Матеріали

12

Необхідні інструменти

16

За цим кресленням виготовляють

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...