Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Harness Straps: Cut Along the Hide With Compass and Round Knife (or Plough), Edges Finished With Bone (Hasluck, 1904)
Tex

Створено

Tex

14. листопад 2026FO
6
0
0
0
0

Harness Straps: Cut Along the Hide With Compass and Round Knife (or Plough), Edges Finished With Bone (Hasluck, 1904)

How a harness maker cuts and finishes straps, from P. N. Hasluck's Harness Making (1904): marked along the hide with an 8 ft straightedge or a compass, cut with the round knife on a cutting-board (or with a plough gauge, 1/2 to 5-1/2 in), always along the hide, then the edges knocked, trimmed with the spokeshave, scraped, sanded and polished with gum and a smooth bone.
Початківець
About 1 hour

Інструкції

1

Widths

Завантаження блокнота Jupyter…
2

Read Harness Making

"Straps are always cut along the hide and not across it, the hide being much stronger lengthways."
3

Lay out

Lay the side on the bench with the back toward you. Mark straight lines with a blunt-pointed awl or seat-awl against a straightedge at least 8 ft long, without cutting the grain. Do not cut lower into the hide than the strap's width; cut shaped pieces from patterns.

Матеріали для цього кроку:

Лимарна шкіраЛимарна шкіра1 штука

Необхідні інструменти ({count})

Повірочна лінійкаПовірочна лінійка
Лимарське шило для набивкиЛимарське шило для набивки
4

Cut

With the round knife: set the compass to the width, run one point along the edge and draw it toward you to leave a line, then cut from the right-hand end on a cutting-board, holding the leather steady with the left hand. With the plough: set the knife on the gauge (1/2 to 5-1/2 in) with the thumb-screw, hold the leather flat and press it forward with the guard tight to the edge. Cut reins first, then traces, back-bands and the rest; linings from the belly.

Необхідні інструменти ({count})

Лимарський циркуль-борозникЛимарський циркуль-борозник
Ніж для шкіриНіж для шкіри
Обробна дошкаОбробна дошка
5

Finish the edges

Knock the edges along to consolidate them, trim them round and level with the spokeshave, run a glass scraper over them and sandpaper. For brown work, wipe with a thin solution of gum and water and rub with brown paper and a smooth bone to a polish. For black, dye, rub dry with a rag, and polish with brown paper and bone.

Матеріали для цього кроку:

ГуміарабікГуміарабік1 штука
Пакувальний крафт-папірПакувальний крафт-папір1 штука
Наждачний папірНаждачний папір1 штука

Необхідні інструменти ({count})

СтругСтруг
Скляний бійСкляний бій
Кісточка для фальцюванняКісточка для фальцювання
МолотокМолоток
6

Troubleshooting

Strap troubleshooting.

Flow

Loading...
7

History and honest limits

From Paul N. Hasluck, **Harness Making** (1904) (checked on the archive.org scan harnessmaking00hasl, pp. 12, 42-44). Using broken glass (cullet) as the glass scraper, the tools and the metric figures are ours.

Матеріали

4

Необхідні інструменти

9

За цим кресленням виготовляють

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...