Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Plough Back-Band With Hooks: Faced, Flock-Padded Back-Band With a Rein Dee (Hasluck, Harness Making, 1904)
Tex

Створено

Tex

13. листопад 2026FO
6
0
0
0
0

Plough Back-Band With Hooks: Faced, Flock-Padded Back-Band With a Rein Dee (Hasluck, Harness Making, 1904)

In plough harness the back-band carries the traces over the horse's back. This is the plough back-band with hooks from Paul N. Hasluck's Harness Making (1904): a 4 in band about 4 ft 4 in over all, with leather facings, a flock-stuffed panel to stop the back getting sore, a dee for the plough rein, and a hook sewn into each end. Every size is his; the picture is our diagram with his Fig. 105 inset.
Середній
About 1 day

Інструкції

1

His sizes in centimetres

Завантаження блокнота Jupyter…
2

Read Harness Making, ch. IX

"In plough gears the ordinary bridle and collar are employed. The back-band is made in various ways. The method with hooks is taken first. The eye of the hook (Fig. 105) is 4 in. wide."
3

Cut and mark the back-band

Cut the leather 3 ft 9 in long and 4 in wide. Turn down 3 in at each end, beat the bend slightly with the hammer to keep it down, and crease it with the screw race, two rows on each side. Mark the centre from each end and draw a line straight across there, then two lines 5 in each side of the centre, 10 in apart.

Матеріали для цього кроку:

Лимарна шкіраЛимарна шкіра1 штука

Необхідні інструменти ({count})

Ніж для шкіриНіж для шкіри
МолотокМолоток
БігувальникБігувальник
Пропановий пальникПропановий пальник
ОлівецьОлівець
РулеткаРулетка
4

Stitch on the facings

Cut two pieces 10-1/2 in long and 3/4 in wide; cut a small piece out of each corner of the working side, then dye and crease that side. Draw a line along the centre of each with the compasses and mark across the centre. Prick out where they go on the back-band, then place one underneath the back-band, centre to centre, as far as the drawn line, and tack it down; place the other the same way on the other side, so the pieces run a little over both lower lines at each end. Stitch, keeping the line close to the edge of the back-band, with thread of three or four cords of coarse hemp.

Матеріали для цього кроку:

Лимарна шкіраЛимарна шкіра1 штука
Фарба для шкіриФарба для шкіри1 штука
Затяжні цвяшкиЗатяжні цвяшки1 штука
Конопляний шпагатКонопляний шпагат1 штука
Бджолиний віскБджолиний віск1 штука

Необхідні інструменти ({count})

Ніж для шкіриНіж для шкіри
БігувальникБігувальник
Лимарський циркуль-борозникЛимарський циркуль-борозник
Пробійник для шкіри (пробійна вилка)Пробійник для шкіри (пробійна вилка)
МолотокМолоток
ШилоШило
Дві лимарські голкиДві лимарські голки
Лимарські лещатаЛимарські лещата
5

Fit the rein dee

Cut a piece of leather 1-1/2 in by 4 in, shave and point both ends, and crease, black and prick it like the side, eight or ten marks per inch. Put a 1-1/2 in tinned dee in the centre of it, lay it flat on the back-band in the centre (measured from both sides, or from the top line to either line below), tack it and stitch. The plough rein runs through this dee; for a pair of horses put the dee on the opposite side of each back-band, for a single horse one on each side of the same back-band.

Матеріали для цього кроку:

Збруйне D-кільцеЗбруйне D-кільце1 штука
Лимарна шкіраЛимарна шкіра1 штука
Фарба для шкіриФарба для шкіри1 штука
Конопляний шпагатКонопляний шпагат1 штука
Бджолиний віскБджолиний віск1 штука

Необхідні інструменти ({count})

Ніж для шкіриНіж для шкіри
Пробійник для шкіри (пробійна вилка)Пробійник для шкіри (пробійна вилка)
ШилоШило
Дві лимарські голкиДві лимарські голки
Лимарські лещатаЛимарські лещата
6

Make the panel

Take linen (or basil) 14 in by 7 in and lay the back-band on it centre to centre, even on both sides. Spot-stitch across the back-band and through the linen along the middle line, like this: // // //. Turn in the linen all round about 1/2 in (basil needs no turning). Make a pleat at each corner at the end of the facing, both exactly the same length, and another opposite each, so the width equals the back-band and facing together (for basil, cut the corner off and stitch the cut instead). Stitch all round, starting about 1-1/2 in from the centre on one side to leave an opening for stuffing, along the cross lines at the bottom, to within 1-1/2 in of the centre on the other side.

Матеріали для цього кроку:

Лляна тканинаЛляна тканина1 штука
Конопляний шпагатКонопляний шпагат1 штука
Бджолиний віскБджолиний віск1 штука

Необхідні інструменти ({count})

НожиціНожиці
ШилоШило
Дві лимарські голкиДві лимарські голки
7

Stuff the panel

Lay the back-band flat on the bench, leather side underneath, openings near the bench edge. Stuff each side rather tightly with flock through the openings, using the stuffing stick; smooth it well towards the sides, flatten with a mallet, and stitch along the openings to the starting point.

Матеріали для цього кроку:

Вовняна набивкаВовняна набивка1 штука
Конопляний шпагатКонопляний шпагат1 штука
Бджолиний віскБджолиний віск1 штука

Необхідні інструменти ({count})

Набивальна палицяНабивальна палиця
Дерев'яний молоток (киянка)Дерев'яний молоток (киянка)
ШилоШило
Дві лимарські голкиДві лимарські голки
8

Sew in the hooks

Cut two saving pieces from a thick, firm face of hide (the face of a gear hide is best), 7 in long and, for a 4 in back-band, 5 in wide. Cut one end slanting to 4 in, the back-band's width, and shave it; round the corners of the other end, leaving it full width; black and crease the edges. Put the hooks in place with the saving pieces under them about 1-1/2 in lower than the end of the hook, and tack them down exactly in the centre. Mark and prick four rows from the hook up to the end of the saving pieces, stitch with four-cord thread, nine or ten stitches per inch, and stitch a line across close to the hook to bind it all together.

Матеріали для цього кроку:

Гак черезсідельникаГак черезсідельника2 штук
Лимарна шкіраЛимарна шкіра1 штука
Фарба для шкіриФарба для шкіри1 штука
Затяжні цвяшкиЗатяжні цвяшки1 штука
Конопляний шпагатКонопляний шпагат1 штука
Бджолиний віскБджолиний віск1 штука

Необхідні інструменти ({count})

Ніж для шкіриНіж для шкіри
БігувальникБігувальник
Пропановий пальникПропановий пальник
Пробійник для шкіри (пробійна вилка)Пробійник для шкіри (пробійна вилка)
МолотокМолоток
ШилоШило
Дві лимарські голкиДві лимарські голки
Лимарські лещатаЛимарські лещата
9

Troubleshooting

Plough back-band troubleshooting.

Flow

Loading...
10

History and honest limits

From **Harness Making**, edited by Paul N. Hasluck, Cassell, 1904 (Project Gutenberg 70169), chapter IX, "Plough Harness", pp. 107-110, Fig. 105; every fraction was checked on the archive.org scan (harnessmaking00hasl). The back-band with chains instead of hooks and the coupling straps are not made here. Linen for the panel (he allows basil), the tools and metric figures are ours; the picture is our diagram with his Fig. 105 inset.

Матеріали

9

Необхідні інструменти

14

За цим кресленням виготовляють

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...