Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Saddle Crupper: Slit Body, Buckled Billet and Paper-Cored Dock (Hasluck, Saddlery, 1904)
Tex

Створено

Tex

13. листопад 2026FO
2
0
0
0
0

Saddle Crupper: Slit Body, Buckled Billet and Paper-Cored Dock (Hasluck, Saddlery, 1904)

A saddle crupper runs from the back of a riding saddle to a padded loop (the dock) under the horse's tail, so the saddle cannot slide forward. This is the full-sized saddle crupper from Paul N. Hasluck's Saddlery (1904): a slit leather body, a buckled billet, and a dock shaped over string and wet brown paper. Every size is his.
Середній
About 1 day

Інструкції

1

His sizes in centimetres

Завантаження блокнота Jupyter…
2

Read Saddlery, ch. V

"Full-sized saddle cruppers (Fig. 9), which are used to prevent the saddle from advancing too much, are made about 1 in. wide, and sometimes a little more."
3

Cut the body

Cut the body about 1 in wide (or a little more) and about 1 ft 6 in long. Slit one end for about 5 in and turn the other end in for a 7/8 in buckle. Shave the points of the slits and the end of the chape.

Матеріали для цього кроку:

Лимарна шкіраЛимарна шкіра1 штука

Необхідні інструменти ({count})

Ніж для шкіриНіж для шкіри
РулеткаРулетка
4

Make the billet and set the buckle

Cut a billet as wide as the buckle and 2 ft 4 in long; trim one end for the buckle and shave the other. Edge both pieces, polish the edges and crease them with a hot checker. Put on the buckle and stitch the billet: the first stitch by the buckle goes over the edge and through chape and billet together, the next through the loop. Run four or five stitches towards the point on each side, and come back to the buckle on the other side, making the last stitch over the side the same as the opposite side.

Матеріали для цього кроку:

Лимарна шкіраЛимарна шкіра1 штука
Залізна пряжка з язичкомЗалізна пряжка з язичком1 штука
Лляна ниткаЛляна нитка1 штука
Бджолиний віскБджолиний віск1 штука

Необхідні інструменти ({count})

Ніж для шкіриНіж для шкіри
КрайкорізКрайкоріз
Гладило для краю шкіриГладило для краю шкіри
БігувальникБігувальник
Пропановий пальникПропановий пальник
ШилоШило
Дві лимарські голкиДві лимарські голки
Лимарські лещатаЛимарські лещата
5

Put on the loop

Put a loop on the flat lower down the body, about 6 in from the buckle, stitching it across at each end.

Матеріали для цього кроку:

Лимарна шкіраЛимарна шкіра1 штука
Лляна ниткаЛляна нитка1 штука
Бджолиний віскБджолиний віск1 штука

Необхідні інструменти ({count})

Ніж для шкіриНіж для шкіри
Оправка для шльовокОправка для шльовок
ШилоШило
Дві лимарські голкиДві лимарські голки
6

Shape the dock core

The dock is much smaller round than a gig crupper dock. Take a piece of string about 1 ft long and roll wet brown paper round it until it is the thickness you need in the middle; thin the ends by cutting the paper before damping it.

Матеріали для цього кроку:

ШнурокШнурок1 штука
Пакувальний крафт-папірПакувальний крафт-папір1 штука

Необхідні інструменти ({count})

НожиціНожиці
ГубкаГубка
РулеткаРулетка
7

Cover the dock

Cut the dock leather about 1 ft 1 in long; it must be soft and pliable, so damp it before stitching. Stitch it over the core as it is, without cutting a groove, drawing it very tightly over the paper. Dry the dock and finish it in shape.

Матеріали для цього кроку:

Лимарна шкіраЛимарна шкіра1 штука
Лляна ниткаЛляна нитка1 штука
Бджолиний віскБджолиний віск1 штука

Необхідні інструменти ({count})

Ніж для шкіриНіж для шкіри
ГубкаГубка
ШилоШило
Дві лимарські голкиДві лимарські голки
Лимарські лещатаЛимарські лещата
8

Join the dock and punch the billet

Stitch the dock to the slits with a splice of about 1-1/4 in. Put about a dozen holes in the billet, and vary the lengths to suit the size of horse.

Матеріали для цього кроку:

Лляна ниткаЛляна нитка1 штука
Бджолиний віскБджолиний віск1 штука

Необхідні інструменти ({count})

Ніж для шкіриНіж для шкіри
ШилоШило
Дві лимарські голкиДві лимарські голки
Пробійник для шкіриПробійник для шкіри
9

Troubleshooting

Saddle crupper troubleshooting.

Flow

Loading...
10

History and honest limits

From **Saddlery**, edited by Paul N. Hasluck, David McKay, 1904 (archive.org saddlery00hasl), chapter V, "Saddle Cruppers, Breastplates, and Other Accessories", saddle cruppers, pp. 40-41, Fig. 9; every fraction was read on the scan. He does not say how the billet fastens to the saddle; check against Fig. 9 and your saddle. The thread, tools and metric figures are ours.

Матеріали

6

Необхідні інструменти

13

За цим кресленням виготовляють

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...