Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Portable Bench Saw: A Lift-Out Power Unit on Trunnions, Its Motor on Spring Bars, Under a Tilting Platform (Henkel, 1928)
Forge

Створено

Forge

13. листопад 2026NO
7
0
0
0
0

Portable Bench Saw: A Lift-Out Power Unit on Trunnions, Its Motor on Spring Bars, Under a Tilting Platform (Henkel, 1928)

Fay M. Henkel of New Rochelle, New York, received US 1,695,188, dated 11 December 1928, for a cheap, compact bench saw in two parts. The stand has a platform that tilts on hinge pins for angled cuts, with a sliding angle follower and a rip guide. The power unit drops into it on trunnions, and a wing nut on a hanging screw raises or lowers the saw. The motor sits on two spring bars that soak up its vibration and keep the belt tight. Lifted out, the power unit stands on the bars' cap nuts and runs an emery wheel. The patent gives no sizes; every size here is ours, and our stand is wood and steel where his is cast.
Просунутий
About 4 days

Інструкції

1

Raising the saw and tilting the platform

Завантаження блокнота Jupyter…
2

Read US 1,695,188

"It will thus be seen that the power unit has a three-point bearing which maintains it against accidental displacement, or, in other words, prevents it from getting out of proper alinement."
3

The stand: frame 1 and legs 3

Make a rectangular frame 460 x 360 mm of 25 x 90 mm hardwood, glued and screwed at the corners. Bolt a 250 mm pine leg 45 x 45 mm in each corner through a short length of steel angle screwed to frame and leg, as his corner plates 4 and lugs 5. Cut a notch 30 in the top of each long side, 60 mm from one end, 21 mm wide and 25 deep, for the trunnions. Screw a steel arm 34 across the other end with a 10.5 mm hole, and a lug 50 with an M10 tapped hole on the side away from the hinges.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини2 штук
Сосновий пиломатеріалСосновий пиломатеріал1 штука
Кутник із м'якої сталіКутник із м'якої сталі1 штука
Смуга з маловуглецевої сталіСмуга з маловуглецевої сталі1 штука
Набір шестигранних болтівНабір шестигранних болтів8 штук
Шурупи по деревуШурупи по дереву24 штук
Столярний клейСтолярний клей1 штука

Необхідні інструменти ({count})

ЕлектролобзикЕлектролобзик
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Струбцина з напрямноюСтрубцина з напрямною
Комбінований кутникКомбінований кутник
РулеткаРулетка
Ножівка по металуНожівка по металу
Набір мітчиків і плашокНабір мітчиків і плашок
Коловорот для мітчиківКоловорот для мітчиків
4

The platform 2

Cut 18 mm plywood 500 x 400 mm and glue a hardwood strip round its underside edges as the flange 8. Cut the opening 13 for the saw, 230 x 30 mm, and a hardwood block 15 to fill it. Rout a square groove 16 the length of the platform for the follower's bar. Screw two steel lugs 9 under one long edge, drilled to line up with holes 10 in the frame, and hinge it with steel pins held by split pins. Run an M10 tilt screw 49 up through lug 50, with a wing nut on its lower end as a handle, its top bearing under the platform.

Матеріали для цього кроку:

Лист фанериЛист фанери1 штука
Дошка з твердої деревиниДошка з твердої деревини1 штука
Смуга з маловуглецевої сталіСмуга з маловуглецевої сталі1 штука
Круглий пруток з маловуглецевої сталіКруглий пруток з маловуглецевої сталі1 штука
ШплінтШплінт2 штук
Шпилька різьбоваШпилька різьбова1 штука
Гайка-баранецьГайка-баранець1 штука
Шурупи по деревуШурупи по дереву16 штук
Столярний клейСтолярний клей1 штука

Необхідні інструменти ({count})

ЕлектролобзикЕлектролобзик
Ручний фрезерРучний фрезер
Набір фрезНабір фрез
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Ножівка по металуНожівка по металу
Струбцина з напрямноюСтрубцина з напрямною
5

The power unit's frame, arbor and trunnions

Bolt two 40 x 6 mm steel flat bars 340 mm long into a frame 24 with spacers. Across one end fix a 20 mm round bar 28 whose ends stand out 25 mm each side as the trunnions 29. At the other end bolt two 30 mm flange bearings for the arbor 26, turned from 30 mm bar like the twin-saw table's, with a collar, a loose flange and an M20 thread for the blade's nut. Bolt a forked steel lug 31 on that end, its slot straddling the hanging screw.

Матеріали для цього кроку:

Смуга з маловуглецевої сталіСмуга з маловуглецевої сталі1 штука
Круглий пруток з маловуглецевої сталіКруглий пруток з маловуглецевої сталі2 штук
Фланцевий підшипникФланцевий підшипник2 штук
Набір шестигранних болтівНабір шестигранних болтів10 штук
Шестигранна гайкаШестигранна гайка3 штук

Необхідні інструменти ({count})

Ножівка по металуНожівка по металу
Свердлильний верстатСвердлильний верстат
Набір сверделНабір свердел
Набір напилківНабір напилків
Слюсарні лещатаСлюсарні лещата
Токарний верстат по металуТокарний верстат по металу
Трикулачковий токарний патронТрикулачковий токарний патрон
Токарний різецьТокарний різець
Цифровий штангенциркуль 6 дюймівЦифровий штангенциркуль 6 дюймів
Розвідний ключРозвідний ключ
Захисні окуляриЗахисні окуляри
6

Spring bars, motor and belt

Bend two strips of spring steel 37, 30 x 3 mm, with a slight bend near one end, and bolt them under the cross bar 28 so they reach out beyond the trunnions. Bolt the motor 36 to them, with cap nuts 40 on the bolts' ends: these are its feet when the unit stands alone. Fit a V-belt pulley 42 on the motor and one 44 on the arbor, and the A-section belt 43. Pivot an arm 45 on the arbor's bearing with a weighted pulley 46 at its free end resting on the belt to take up the slack. Have the motor wired to a switch.

Матеріали для цього кроку:

Смуга пружинної сталіСмуга пружинної сталі1 штука
ЕлектродвигунЕлектродвигун1 штука
Шків клинового паса (профіль A)Шків клинового паса (профіль A)3 штук
Клиновий пас (переріз A)Клиновий пас (переріз A)1 штука
Смуга з маловуглецевої сталіСмуга з маловуглецевої сталі1 штука
Набір шестигранних болтівНабір шестигранних болтів6 штук
Шестигранна гайкаШестигранна гайка6 штук
Установчий гвинт із чашоподібним кінцемУстановчий гвинт із чашоподібним кінцем3 штук
Вимикач живленняВимикач живлення1 штука

Необхідні інструменти ({count})

Слюсарні лещатаСлюсарні лещата
Свердлильний верстатСвердлильний верстат
Набір сверделНабір свердел
Розвідний ключРозвідний ключ
Набір шестигранних ключівНабір шестигранних ключів
7

Put the unit in and set the saw

Fit the 200 mm blade on the arbor. Hang an M10 screw 32 from arm 34 with its head 35 on top. Lower the power unit in, the trunnions into the notches 30 and the forked lug 31 round the screw, and run a wing nut 36 up under the lug. Turn the wing nut to raise the blade through the opening to the depth wanted.

Матеріали для цього кроку:

Circular Saw Blade SetCircular Saw Blade Set1 штука
Шпилька різьбоваШпилька різьбова1 штука
Гайка-баранецьГайка-баранець1 штука
Плоска шайбаПлоска шайба2 штук

Необхідні інструменти ({count})

Розвідний ключРозвідний ключ
8

Follower and rip guide

Angle follower: a hardwood bar 17 sliding in the groove, with an angle fence 18 clamped at any angle by a wing nut 19. Rip guide 20: a hardwood bar across the platform held by two hook bolts 21 that hook under the flange 8, with wing nuts 22. Mark a scale 23 on the platform's ends to set it.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини1 штука
Шпилька різьбоваШпилька різьбова1 штука
Гайка-баранецьГайка-баранець3 штук
Смуга з маловуглецевої сталіСмуга з маловуглецевої сталі1 штука

Необхідні інструменти ({count})

ЕлектролобзикЕлектролобзик
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Ножівка по металуНожівка по металу
Слюсарні лещатаСлюсарні лещата
РулеткаРулетка
9

Try it, and as a grinder

With the platform flat, check the blade is square to it with the square, rip a board along the guide and crosscut another against the follower. Tilt the platform with the tilt screw (and the block under it for steep angles) and check the angle with the protractor. Lift the power unit out, stand it on its cap nuts, swap the blade for the grinding wheel, swing the idler arm to the belt's other side, and run it.

Необхідні інструменти ({count})

Шліфувальний кругШліфувальний круг
Комбінований кутникКомбінований кутник
ТранспортирТранспортир
Захисні окуляриЗахисні окуляри
Захист слуху (навушники, SNR 30 дБ)Захист слуху (навушники, SNR 30 дБ)
10

Troubleshooting

Portable bench saw troubleshooting.

Flow

Loading...
11

History and honest limits

**Fay M. Henkel** of New Rochelle, New York, US 1,695,188, dated 11 December 1928, filed 28 April 1927. He claimed a supporting unit with a platform and a power unit with a frame, "trunnions on the end of said frame, said supporting unit having recesses therein receiving the trunnions", a bearing and arbor, spring bars and a motor fixed to them, pulleys and a belt; and the spring bars' couplings serving as feet when the unit is removed. His frame, platform and legs are castings; ours are hardwood, plywood and steel. His bearing is a sleeve with a grease cup; ours are two greased flange bearings. He gives no sizes, motor or speeds; those are ours.

Матеріали

22

Необхідні інструменти

24

За цим кресленням виготовляють

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...