Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Instant-Read Thermometer: Digital, with a Stainless Probe That Pivots on the Case (Cook, US 5,018,875, 1991)
Penny

Створено

Penny

3. листопад 2026DK
10
0
0
0
0

Instant-Read Thermometer: Digital, with a Stainless Probe That Pivots on the Case (Cook, US 5,018,875, 1991)

A pocket digital thermometer. A thin stainless steel probe with a thermistor in its tip pivots on a small, flat-sided case, so you can push the probe into food and turn the display to face you. A button cell runs a chip and a liquid crystal display, and a push button updates the reading at once. The angled case will not roll off a table. Result: a thin-probe digital thermometer for food and air. Source: T. A. Cook (PSG Industries), US 5,018,875 (1991). Unknown: the circuit, the range, the case size. Picture: the patent drawing.
Середній
Unknown

Інструкції

1

Make the probe

Cut a type 304 stainless steel tube about 0.166 in (4.0 mm) across and 5 in (120 mm) long, and close one end. Set a thermistor inside the closed tip and run its two wires up the tube. Aluminium or titanium would also serve.

Матеріали для цього кроку:

Труба з нержавкої сталіТруба з нержавкої сталі1 probe
Набір термісторів NTCНабір термісторів NTC1 thermistor
Мідний дрітМідний дріт1 interconnecting wires

Необхідні інструменти ({count})

Ножівка по металуНожівка по металу
ПаяльникПаяльник
2

Mould the pivot boss and case

Mould from ABS a cylindrical pivot boss with a recess for the probe's open end and a channel right through it for the wires. Mould the case in an upper and a lower half that snap together, wider at the display end and tapering to the probe end so it cannot roll, with two projecting supports at the probe end, each with a pivot hole. Not given: the sizes.

Матеріали для цього кроку:

Гранули ABSГранули ABS1 boss and case

Необхідні інструменти ({count})

Ливарна машинаЛиварна машина
Невідомі розміриНевідомі розміри
3

Fit the electronics and assemble

In the case, fit an integrated circuit that turns the thermistor's resistance into a reading on a liquid crystal display at the wide end, with a push button beside it that updates the reading at once. Add a compartment for a 1.5 V button cell (Eveready E675, IEC R07) under a cover that locks with a quarter turn. Push the probe into the boss, lead the wires through the channel to the circuit, and clamp the boss ends in the pivot holes as the halves snap together; friction holds whatever angle you set. In use, push the probe in, turn the display to face you and press the button. Not given: the circuit (the patent points to US 4,536,851).

Матеріали для цього кроку:

Друкована платаДрукована плата1 штука
Інтегральна мікросхемаІнтегральна мікросхема1 штука
Сегментний РК-індикаторСегментний РК-індикатор1 штука
КнопкаКнопка1 штука
Дисковий елемент живлення 1,5 ВДисковий елемент живлення 1,5 В1 штука
Дріт припоюДріт припою1 as needed

Необхідні інструменти ({count})

ПаяльникПаяльник

Матеріали

10

Необхідні інструменти

4

Пов'язані креслення

Ці креслення діляться знаннями — техніки, матеріали або принципи

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...