Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Kitchen Funnel with Air-Vent Ribs, 3D Printed in PETG
3DBonanza

Створено

3DBonanza

18. листопад 2026US
5
0
0
0
0

Kitchen Funnel with Air-Vent Ribs, 3D Printed in PETG

A 120 mm kitchen funnel for bottling wine, cider or juice, printed in one piece in PETG. Three small ribs along the outside of the spout hold it off the bottle neck so air can come out while the liquid goes in, so it pours without glugging. A common, open design; all sizes are ours, and we have not printed or tested it yet.
Початківець
About 4 hours, mostly printing

Інструкції

1

Our funnel's numbers

Завантаження блокнота Jupyter…
2

Make it fit your bottles

Optional: change TOP_D or the spout sizes and run it in FreeCAD: OUT=. TOP_D= freecadcmd build_all.py
build_all.pypython
"""Batch 2451 -- PETG kitchen funnel with air-vent ribs on the spout. Open, common design (Admiral 2026-11-18: "it is open knowledge on
what a funnel is"); all sizes ours. Run: OUT=<dir> [TOP_D=120] freecadcmd build_all.py  (mm; printed rim-down on the bed, no supports)."""
import math, os
import FreeCAD as App, Part, MeshPart
OUT = os.environ["OUT"]
V = App.Vector
TOP_D = float(os.environ.get("TOP_D", "120"))     # rim inside diameter
WALL = 1.8
CONE_HALF = 30.0                                   # half-angle: 60 degree cone
SPOUT_TOP_D, SPOUT_TIP_D, SPOUT_L = 16.0, 13.0, 50.0   # spout outside, tapering so it fits bottle necks
RIB_H, RIB_W = 1.2, 1.6                            # three vent ribs on the spout's outside
RIM_LIP = 4.0                                      # flat lip round the rim (bed adhesion, stiffness)
r_top = TOP_D / 2
r_neck_in = SPOUT_TOP_D / 2 - WALL
cone_h = (r_top - r_neck_in) / math.tan(math.radians(CONE_HALF))
def save(sh, name):
    bb = sh.BoundBox
    print(name, "valid", sh.isValid(), "solids", len(sh.Solids), "bbox", [round(v, 1) for v in (bb.XLength, bb.YLength, bb.ZLength)],
          "volume_cm3", round(sh.Volume / 1000, 1))
    MeshPart.meshFromShape(Shape=sh, LinearDeflection=0.03, AngularDeflection=0.12).write(os.path.join(OUT, name + ".stl"))
# z up: spout tip at z=0, cone above, rim at the top
off = WALL / math.cos(math.radians(CONE_HALF))
outer = Part.makeCone(SPOUT_TOP_D / 2, r_top + off, cone_h, V(0, 0, SPOUT_L))
inner = Part.makeCone(r_neck_in, r_top, cone_h + 0.01, V(0, 0, SPOUT_L))
spout_o = Part.makeCone(SPOUT_TIP_D / 2, SPOUT_TOP_D / 2, SPOUT_L + 0.01, V(0, 0, 0))
spout_i = Part.makeCone(SPOUT_TIP_D / 2 - WALL, r_neck_in, SPOUT_L + 0.02, V(0, 0, -0.01))
body = outer.fuse(spout_o).cut(inner).cut(spout_i)
lip = Part.makeCylinder(r_top + off + RIM_LIP, 1.6, V(0, 0, SPOUT_L + cone_h - 1.6)).cut(Part.makeCylinder(r_top - 0.5, 3, V(0, 0, SPOUT_L + cone_h - 2)))
body = body.fuse(lip)
r_at = lambda z: (SPOUT_TIP_D + (SPOUT_TOP_D - SPOUT_TIP_D) * z / SPOUT_L) / 2
for a in (0, 120, 240):
    z0, z1 = 2.0, SPOUT_L - 1.0
    pts = [V(r_at(z0) - 0.4, -RIB_W / 2, z0), V(r_at(z0) + RIB_H, -RIB_W / 2, z0), V(r_at(z1) + RIB_H, -RIB_W / 2, z1), V(r_at(z1) - 0.4, -RIB_W / 2, z1)]
    rib = Part.Face(Part.makePolygon(pts + [pts[0]])).extrude(V(0, RIB_W, 0))
    rib.rotate(V(0, 0, 0), V(0, 0, 1), a)
    body = body.fuse(rib)
body = body.removeSplitter()
save(body, "petg-kitchen-funnel")
cap = math.pi * cone_h / 3 * (r_top**2 + r_top * r_neck_in + r_neck_in**2) / 1000
print("cone height", round(cone_h, 1), "mm; holds about", round(cap), "ml in the cone")
print("spout", SPOUT_TOP_D, "->", SPOUT_TIP_D, "mm outside, bore", round(SPOUT_TIP_D - 2 * WALL, 1), "mm at the tip")
print("air gap per rib, in a neck the spout just fits:", RIB_H, "x", "(gap between ribs)")

Необхідні інструменти ({count})

Цифровий штангенциркуль 6 дюймівЦифровий штангенциркуль 6 дюймів
3

Print the funnel

Print it rim down on the bed, no supports; the cone and spout grow upward. PETG sold for food contact, a stainless steel nozzle (brass nozzles can contain lead), 0.2 mm layers, at least 3 walls.
Файл дизайнуSTLCC0 - Free

Матеріали для цього кроку:

Філамент PETGФіламент PETG60 г

Необхідні інструменти ({count})

3D-принтер FDM3D-принтер FDM
Набір сопел для 3D-принтераНабір сопел для 3D-принтера
4

Clean it up

Trim any strings or blobs, especially inside the spout and between the ribs. Check the spout is clear.

Необхідні інструменти ({count})

Макетний ніжМакетний ніж
5

Check the fit

Put the spout into a bottle: the ribs should touch the neck and leave gaps between them. Pour water through and watch it run without glugging.
Крок 5 - Image 1

Необхідні інструменти ({count})

Скляні бутлі з коркамиСкляні бутлі з корками
ВодаВода
6

Sanitise

Soak it in no-rinse sanitiser mixed as its label says. Do not boil it: PETG softens at about 80 °C.

Необхідні інструменти ({count})

Дезінфекційний засібДезінфекційний засіб
ВодаВода
7

Troubleshooting

Funnel problems and fixes.

Flow

Loading...
8

Honest limits

A common, open design, drawn by us in FreeCAD; every size is ours. The ribs were checked by slicing the model; the funnel has not been printed or poured through by us yet. Sanitise before every use and replace it when scratched.

Матеріали

1

Необхідні інструменти

7

Файли дизайну

1

За цим кресленням виготовляють

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...