Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Three-Piece Airlock, 3D Printed in PETG
3DBonanza

Створено

3DBonanza

18. листопад 2026US
4
0
0
1
0

Three-Piece Airlock, 3D Printed in PETG

An airlock lets the carbon dioxide of a fermenting beer, wine or cider out through a little water, and keeps outside air out. This one has the four parts of the "standard type device" named in L. P. Beadle's 1980 US patent 4,218,964: a cap, a tapered stem, a housing two-thirds full of water, and a cone member. It prints in three pieces in PETG. All sizes are ours, and we have not printed or tested it yet: the leak test below comes first.
Початківець
About 5 hours, mostly printing

Інструкції

1

Seal pressure and water back-flow

Завантаження блокнота Jupyter…
2

Read US 4,218,964

"Housing 27 is filled two-thirds full with water, cone 28 is inserted and cap 25 is secured ... excess gas escapes by bubbling through the water in lock 14 so as to protect the beer ingredients within container 11 from contact with outside air." The picture is our section: gas goes up the stem, under the cone member's rim and out of the cap.
Крок 2 - Image 1
3

Print the housing and stem

Stand it on the stem's tip with a 10 mm brim; the 45 degree cone under the floor needs no supports. PETG sold for food contact, a stainless steel nozzle (brass nozzles can contain lead), 0.2 mm layers, at least 4 walls so no water finds a path between the layers.
Файл дизайнуSTLCC0 - Free

Матеріали для цього кроку:

Філамент PETGФіламент PETG15 г

Необхідні інструменти ({count})

3D-принтер FDM3D-принтер FDM
Набір сопел для 3D-принтераНабір сопел для 3D-принтера
4

Print the cone member

Print it upside down, closed end on the bed. PETG sold for food contact, a stainless steel nozzle (brass nozzles can contain lead), 0.2 mm layers, at least 4 walls so no water finds a path between the layers.
Файл дизайнуSTLCC0 - Free

Матеріали для цього кроку:

Філамент PETGФіламент PETG3 г

Необхідні інструменти ({count})

3D-принтер FDM3D-принтер FDM
Набір сопел для 3D-принтераНабір сопел для 3D-принтера
5

Print the cap

Print it upside down, top on the bed. PETG sold for food contact, a stainless steel nozzle (brass nozzles can contain lead), 0.2 mm layers, at least 4 walls so no water finds a path between the layers.
Файл дизайнуSTLCC0 - Free

Матеріали для цього кроку:

Філамент PETGФіламент PETG3 г

Необхідні інструменти ({count})

3D-принтер FDM3D-принтер FDM
Набір сопел для 3D-принтераНабір сопел для 3D-принтера
6

Clean the parts

Take off the brim. Turn a 5 mm drill bit through the stem by hand to clear any strings. Check the stem: 10.0 mm at the top, 8.5 mm at the tip.

Необхідні інструменти ({count})

Набір сверделНабір свердел
Цифровий штангенциркуль 6 дюймівЦифровий штангенциркуль 6 дюймів
7

Leak test

Fill the housing with water to the groove. Stand it in a dry glass for an hour. Any drop on the outside or in the glass means a leak: print again.

Необхідні інструменти ({count})

ВодаВода
8

Sanitise

Soak all three parts in no-rinse sanitiser mixed as its label says. Do not boil them: PETG softens at about 80 °C.

Необхідні інструменти ({count})

Дезінфекційний засібДезінфекційний засіб
ВодаВода
9

Assemble and fill

Drop the cone member over the riser tube. Fill the housing to the groove with sanitiser solution, not plain water. Push the cap on.

Необхідні інструменти ({count})

Дезінфекційний засібДезінфекційний засіб
ВодаВода
10

Fit it to the fermenter

Push the stem into the bored stopper or the lid's hole. The stem gets thinner towards the tip, so it wedges tight, as in Beadle's patent. Gas must bubble through the water, never round the stem.

Необхідні інструменти ({count})

Гумові коркиГумові корки
11

Troubleshooting

Airlock problems and fixes.

Flow

Loading...
12

History and honest limits

**Leigh P. Beadle**, US 4,218,964, "Lid construction for fermentation container", filed 21 May 1979, issued 26 August 1980, assigned to Specialty Products International Ltd. His invention was the lid; he calls the airlock "a standard type device" and names its parts: cap 25, tapered stem 26, housing 27 and cone member 28. He gives no sizes and no material for the lock. Ours: every size, the riser tube, the three ribs, the vent holes, the posts that stop the cone member lifting more than 3.4 mm, and PETG. Checked in CAD for fit; not yet printed or brewed with by us.

Матеріали

1

Необхідні інструменти

7

Файли дизайну

3

За цим кресленням виготовляють

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...