Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Star-Dasher Crank Churn: Geared Crank and Flywheel Drive Two Notched Dashers Set Point Over Gap
Martin

Створено

Martin

9. листопад 2026NO
10
0
0
0
0

Star-Dasher Crank Churn: Geared Crank and Flywheel Drive Two Notched Dashers Set Point Over Gap

Lorenzo Lake of Middlebury, Pennsylvania, received US 24,845, dated 19 July 1859, for an upright dash churn worked by gearing so that a child could churn even a very large churn. A handle turns a large wheel driving a wheel half its size on a crank shaft with a balance wheel; the crank's pitman works the staff up and down through a guide. The staff carries two dashers of boards with V-shaped slots in their ends, set so the points of one lie over the gaps of the other, cutting the cream as it escapes going down and up and dashing it against the sides. This rung builds it with printed gears over a 20-litre bucket.
Середній
About 2 days, plus printing

Інструкції

1

Strokes per turn of the handle

Завантаження блокнота Jupyter…
2

A crank and pitman working the staff, before it

Dorsey's pitman also turned the staff. Lake's only lifts it, through gearing and a balance wheel for speed.
3

Read US 24,845

"... these dashers are so placed upon the staff that the sharpened ends of the boards thus cut, will cover the spaces left between the boards in the dasher immediately above or below—so that when operated in the churn the cream will be more thoroughly cut and the globules will be more easily and speedily broken."
4

Print the wheel E

The 40-tooth wheel for the handle's shaft. PETG, 0.2 mm layers, 50 % infill, 5 walls.
Файл дизайнуSTLCC0 - Free
5

Print the wheel F

The 20-tooth wheel for the crank shaft. PETG, 0.2 mm layers, 50 % infill, 5 walls.
Файл дизайнуSTLCC0 - Free
6

Platform, upright and frame

Screw a pine platform C 500 x 550 mm. Stand a 70 mm upright C' 990 mm tall at its back, braced. Screw a hardwood beam 130 x 255 x 40 mm out from the upright's top toward the front, and hang three hardwood blocks from it, each bored 20.5 mm 900 mm above the floor: two either side of the crank, 90 mm apart, for shaft G, and one 90 mm to the side for wheel E's shaft. Screw a hardwood guide arm I from the upright to over the bucket 430 mm up, with a 26 mm square hole.

Матеріали для цього кроку:

Соснова дошкаСоснова дошка2 штук
Хвойний брус 70x70 ммХвойний брус 70x70 мм2 штук
Дошка з твердої деревиниДошка з твердої деревини2 штук
Шуруп по дереву № 10 x 3"Шуруп по дереву № 10 x 3"20 штук
Столярний клейСтолярний клей1 штука

Необхідні інструменти ({count})

Ручна пилкаРучна пилка
Акумуляторний дрильАкумуляторний дриль
Набір перових сверделНабір перових свердел
СтамескиСтамески
Будівельний рівеньБудівельний рівень
РулеткаРулетка
7

Crank shaft G, wheels and handle

Make the crank from two hardwood webs 30 x 10 mm, a 12 mm stainless pin 50 mm off the axis between them, and two 20 mm steel stubs, one each side, run through the hanging blocks. Fix wheel F on the rear stub and a plywood balance wheel B 300 mm across, with spokes, on the front stub. Run a 20 mm steel shaft through the third block with wheel E meshing with F, and a hardwood handle M 57 mm long with a dowel grip on its end.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини1 штука
Пруток із нержавкої сталіПруток із нержавкої сталі1 штука
Сталевий пруток-заготовкаСталевий пруток-заготовка2 штук
Філамент PETGФіламент PETG1 штука
Лист фанериЛист фанери1 штука
Шканти з твердої деревиниШканти з твердої деревини1 штука
Столярний клейСтолярний клей1 штука
Набір шестигранних болтівНабір шестигранних болтів4 штук
Самоконтрувальна гайка з нейлоновим кільцемСамоконтрувальна гайка з нейлоновим кільцем4 штук

Необхідні інструменти ({count})

3D-принтер FDM3D-принтер FDM
ЕлектролобзикЕлектролобзик
Ножівка по металуНожівка по металу
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Напилки (ручний напилок)Напилки (ручний напилок)
Розвідний ключРозвідний ключ
8

Staff, dashers and pitman

Cut two plywood dashers L, each a 16-point star 250 mm across with its notches 20 mm deep, and a 25 mm square hole in the middle. Glue them on a 25 mm square hardwood staff D 150 mm apart, the upper turned half a point from the lower. Cut a hardwood pitman H 300 mm between centres with a fork at its foot; fit a hardwood thimble J on the staff's top and push an 8 mm stainless rod a through the fork, thimble and staff. Put the staff through the guide and the bucket's lid and set the lower dasher 25 mm off the floor at the bottom of the stroke.

Матеріали для цього кроку:

Лист фанериЛист фанери1 штука
Дошка з твердої деревиниДошка з твердої деревини2 штук
Столярний клейСтолярний клей1 штука
Пруток із нержавкої сталіПруток із нержавкої сталі1 штука
Плоска шайбаПлоска шайба2 штук
Відро на 20 літрівВідро на 20 літрів1 штука

Необхідні інструменти ({count})

ЕлектролобзикЕлектролобзик
Ручна пилкаРучна пилка
СтамескиСтамески
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Наждачний папірНаждачний папір
9

The build in 3D

FreeCAD model of this build, half the bucket cut away: the platform and upright, the beam with its hanging blocks, the split crank shaft with balance wheel and wheel F, wheel E and handle M, the forked pitman and thimble, the staff through its guide, and the two star dashers. It was checked at eight crank angles.
Файл дизайнуBLENDCC0 - Free
10

Churn

Pour about 10 litres of heavy cream at about 15 °C into the bucket, checked with the thermometer, and put the lid on round the staff. Turn the handle steadily and time it. When the butter comes, pull pin a, lift the staff out, pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

Матеріали для цього кроку:

Жирні вершкиЖирні вершки10 l
Крупна морська сільКрупна морська сіль1 штука
ВодаВода1 штука

Необхідні інструменти ({count})

Термометр зі щупом, що лишається в стравіТермометр зі щупом, що лишається в страві
СекундомірСекундомір
Цифрові кухонні вагиЦифрові кухонні ваги
Велика миска з нержавкої сталіВелика миска з нержавкої сталі
11

Troubleshooting

Star-dasher churn troubleshooting.

Flow

Loading...
12

History and honest limits

**Lorenzo Lake** of Middlebury, Tioga County, Pennsylvania, assignor to himself and William Patton of Towanda, US 24,845, 19 July 1859, "Churn". He claimed the dasher L worked by the devices described, not the gearing as such. His only proportion is wheel F about half wheel E. His dashers are boards with V-slotted ends; ours are plywood stars cut to the same pattern. Every size is ours.

Матеріали

17

Необхідні інструменти

17

Файли дизайну

3

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...