Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Spiral-Edge Countersinks: One Curved Slot Up the Cone Makes an Edge That Slices Instead of Scraping (Laursen, 1926)
Forge

Створено

Forge

13. листопад 2026NO
6
0
0
0
0

Spiral-Edge Countersinks: One Curved Slot Up the Cone Makes an Edge That Slices Instead of Scraping (Laursen, 1926)

Laust K. Laursen of College Station, Texas, received US 1,586,559, dated 1 June 1926. Ordinary countersinks have straight edges in radial planes, which press on the wood all at once and scrape it, like pushing a knife straight down on a loaf. Laursen curved the edge into a spiral running up and out from near the point, ahead of the radial line as the tool turns. It reaches the wood a little at a time and slices, leaving a smooth countersink without chatter. His simplest form is one curved slot in the cone, its leading edge sharpened and the cone behind it relieved. We make a set of three in tool steel. The patent gives no sizes; every size here is ours.
Середній
About 1 day

Інструкції

1

Why a spiral edge shears

Завантаження блокнота Jupyter…
2

Read US 1,586,559

"In this particular form the spiral extends outwardly in the direction of action, that is to say, the usual direction of rotation of a countersink is clockwise, viewed from the top, or counterclockwise, as viewed from the bottom." "It has been found that a hole formed with a countersink as shown in Figs. 1 and 2 will be very smooth and uniform on the inside."
3

Turn the blanks

From octagonal tool steel turn three blanks: a 90 degree cone 3 to a point, 12, 16 and 20 mm across at its base, then the body 1 and an 8 mm shank 2 50 mm long with three filed flats. Heat each to a cherry red and let it cool slowly in the air to soften it.

Матеріали для цього кроку:

Восьмигранник з інструментальної сталіВосьмигранник з інструментальної сталі2 штук

Необхідні інструменти ({count})

Токарний верстат по металуТокарний верстат по металу
Трикулачковий токарний патронТрикулачковий токарний патрон
Токарний різецьТокарний різець
Відрізний різецьВідрізний різець
ТранспортирТранспортир
Цифровий штангенциркуль 6 дюймівЦифровий штангенциркуль 6 дюймів
Набір напилківНабір напилків
ГорноГорно
Ковальські кліщіКовальські кліщі
Захисні окуляриЗахисні окуляри
4

File the spiral slot 4

Blue the cone and scribe a spiral on it from 1 mm from the point to the rim, turning a quarter of the way round, leaning ahead in the direction the tool turns (clockwise seen from the shank). File a slot along it with a round needle file, 2 to 3 mm wide and 1.5 mm deep at the rim, shallower towards the point. Sharpen the slot's leading edge 5 and file the cone behind it slightly lower, so only the edge touches the work.

Необхідні інструменти ({count})

Набір надфілівНабір надфілів
Машинні лещатаМашинні лещата
Набір напилківНабір напилків
5

Harden and temper

Heat each head to a cherry red, until a magnet no longer sticks, and quench it point first in water, moving it about. Rub it bright with a stone, heat the shank gently 20 mm behind the head, and quench again as soon as a light straw colour reaches the cutting edge.

Необхідні інструменти ({count})

ГорноГорно
Ковальські кліщіКовальські кліщі
Невеликий магнітНевеликий магніт
Гартівна діжкаГартівна діжка
ВодаВода
Точильний каміньТочильний камінь
Зварювальні рукавиціЗварювальні рукавиці
Захисні окуляриЗахисні окуляри
6

Hone and test

Hone the edge lightly with the stone. Drill screw holes in hardwood and countersink them: the edge should cut a smooth bell with no chatter and throw curled shavings out of the slot.

Необхідні інструменти ({count})

Точильний каміньТочильний камінь
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Дошка з твердої деревиниДошка з твердої деревини
Захисні окуляриЗахисні окуляри
7

Troubleshooting

Spiral countersink troubleshooting.

Flow

Loading...
8

History and honest limits

**Laust K. Laursen** of College Station, Texas, US 1,586,559, dated 1 June 1926, filed 1 August 1925. He set out to give a countersink "a cutting blade or edge so arranged that it will tend to cut, rather than scrape, the work", each edge curving spirally of the tool. He shows three forms: one slot in a hollow head, two split halves with twin edges, and a many-bladed one he found better for metal; we make the first, in one piece. He gives no sizes or angle; our 90 degree cones, quarter-turn spiral and the house hardening are ours.

Матеріали

1

Необхідні інструменти

20

За цим кресленням виготовляють

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...