Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Hind Horseshoe: Round-Pointed Toe, No Seating, Nail Holes in the Front Two-Thirds (Lungwitz and Adams, Text-Book of Horseshoeing, 1913)
Forge

Створено

Forge

13. листопад 2026NO
3
0
0
0
0

Hind Horseshoe: Round-Pointed Toe, No Seating, Nail Holes in the Front Two-Thirds (Lungwitz and Adams, Text-Book of Horseshoeing, 1913)

A flat hind horseshoe from Lungwitz and Adams, A Text-Book of Horseshoeing (1913). It is made "in like manner" as the front shoe, but the branches are bent to a different curve, giving a round-pointed toe, the hoof side is not concaved, and the nail holes run further back. Fitting and nailing the shoe to the horse, calks and clips are not covered here.
Середній
8-15 minutes a pair, once practised

Інструкції

1

Bar length and sizes

Завантаження блокнота Jupyter…
2

Read Lungwitz and Adams

"The hind shoe is made in like manner, but the branches are not bent in a circle but given that form shown in Fig. 106."
3

Measure and cut the bar

Measure the hoof from the point of the toe to the buttress and its greatest width; add them for the bar length. Trace the outline on stiff paper if you want to keep it. Cut the bar.

Матеріали для цього кроку:

Пруток кованого залізаПруток кованого заліза1 штука

Необхідні інструменти ({count})

РулеткаРулетка
ОлівецьОлівець
Аркуші щільного паперуАркуші щільного паперу
Кувальне горноКувальне горно
Підсічка ковадлаПідсічка ковадла
Ковальські кліщіКовальські кліщі
4

Bend the outer branch to the hind curve

Heat the bar white-hot just beyond its middle and bend it over the sledge head on the anvil face with the turning hammer, as for the front shoe, but bend the branch to the flatter, angled curve of his Fig. 106, not to a circle. The outer branch is made first, the right shoe first in a pair. Draw out the end with the sledge.

Необхідні інструменти ({count})

Кувальне горноКувальне горно
Шперак (ковадельце з дзьобом)Шперак (ковадельце з дзьобом)
Вантажні саниВантажні сани
Молоток для заокругленняМолоток для заокруглення
Ковальські кліщіКовальські кліщі
5

Bevel, flatten and shape

Bevel the branch on the horn, then flatten it. Bending the toe of a hind shoe backs up the inner edge and thins the outer, so hammer the shoe smooth and even. Shape it so the toe is round-pointed, "yet not too much so", as in his Fig. 116.

Необхідні інструменти ({count})

Шперак (ковадельце з дзьобом)Шперак (ковадельце з дзьобом)
Молоток для заокругленняМолоток для заокруглення
Ковальські кліщіКовальські кліщі
6

Round the inner edge and fuller

Concaving is not necessary: just round the inner edge of the web. Fuller the ground side as for the front shoe, to about two-thirds of the thickness.

Необхідні інструменти ({count})

Шперак (ковадельце з дзьобом)Шперак (ковадельце з дзьобом)
Фулер (прутик для канавок)Фулер (прутик для канавок)
Вантажні саниВантажні сани
Молоток для заокругленняМолоток для заокруглення
Ковальські кліщіКовальські кліщі
7

Stamp the nail holes

Stamp and pritchel the nail holes in the front two-thirds of the shoe, none at the toe: usually one more than a front shoe, seldom more than eight. Set each as far from the outer edge as the wall is thick; on a hind hoof the wall is nearly as thick at the quarters as at the toe.

Необхідні інструменти ({count})

Шперак (ковадельце з дзьобом)Шперак (ковадельце з дзьобом)
Гарячий пробійникГарячий пробійник
Пробійник для цвяхових отворівПробійник для цвяхових отворів
Молоток для заокругленняМолоток для заокруглення
Ковальські кліщіКовальські кліщі
8

Make the second branch and finish

Make the inner branch the same way, turned to the left. Go over the outer edge on the horn and hammer the bearing surface smooth and level. Rough it out in two heats if you can.

Необхідні інструменти ({count})

Кувальне горноКувальне горно
Шперак (ковадельце з дзьобом)Шперак (ковадельце з дзьобом)
Молоток для заокругленняМолоток для заокруглення
Фулер (прутик для канавок)Фулер (прутик для канавок)
Гарячий пробійникГарячий пробійник
Пробійник для цвяхових отворівПробійник для цвяхових отворів
Ковальські кліщіКовальські кліщі
9

Troubleshooting

Hind shoe troubleshooting.

Flow

Loading...
10

History and honest limits

From **A Text-Book of Horseshoeing**, by A. Lungwitz and John W. Adams, 11th edition, J. B. Lippincott, 1913 (Project Gutenberg 66786), chapter III F. His Fig. 116 shows a hind shoe with toe- and heel-calks; the calks and the toe-clip are not made here, as this chapter gives no method for forging heel-calks or drawing clips. Fitting and nailing are not covered. The metric figures are ours.

Матеріали

1

Необхідні інструменти

12

За цим кресленням виготовляють

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...