МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Nalbinding a Wool Sock in the Oslo Stitch — The Looped Fabric Before Knitting
Tex

Створено

Tex

2. липень 2026FO
58
0
0
0
0

Nalbinding a Wool Sock in the Oslo Stitch — The Looped Fabric Before Knitting

Long before knitting, people made warm, hard-wearing socks and mittens by nalbinding — looping short lengths of wool with a single flat needle. Unlike knitting, which pulls loops through loops with two rods and can unravel, nalbinding passes the whole working thread through each stitch, giving a dense, felt-firm fabric that will not run. This blueprint works the simple Oslo stitch into a tube for a sock or mitten, joining new wool with a felted splice rather than a knot — exactly as the Vikings did.
Середній
4

Інструкції

1

Cut a short working length

Cut about an arm's length of wool yarn — not a whole ball. In nalbinding the entire length is pulled through every stitch, so you work with short pieces and splice on more as needed.

Матеріали для цього кроку:

Моток вовняної пряжіМоток вовняної пряжі1 штука

Необхідні інструменти ({count})

НожиціНожиці
2

Thread the flat needle

Thread the yarn through the eye of the flat nalbinding needle. The needle is broad, blunt and eyed at one end — bone, antler or wood — and never has a hook.

Необхідні інструменти ({count})

Голка для нальбіндингуГолка для нальбіндингу
3

Make the foundation loops

Loop the yarn around your thumb and make a short chain of starting loops. These foundation loops are the base row that every following stitch will anchor into.

Необхідні інструменти ({count})

Голка для нальбіндингуГолка для нальбіндингу
4

Work the Oslo stitch

Pass the needle under the thumb loop and up through the working loop to form the Oslo stitch — the simplest nalbinding stitch. Draw each stitch snug and even, building the first row.

Необхідні інструменти ({count})

Голка для нальбіндингуГолка для нальбіндингу
5

Join into a round

For a sock or mitten, connect the ends of the first row into a ring by stitching the last stitch into the first, so you can then work round and round to form a tube.

Необхідні інструменти ({count})

Голка для нальбіндингуГолка для нальбіндингу
6

Work in a spiral

Continue in a spiral, anchoring each new Oslo stitch into the loop of the row below. Keep the tension steady so the tube grows even in width — this becomes the leg of the sock.

Необхідні інструменти ({count})

Голка для нальбіндингуГолка для нальбіндингу
7

Splice in new yarn

When the length runs short, join a new piece with a felted splice, not a knot: untwist and overlap the two wool ends, wet them, and roll them briskly between your palms until the fibres felt into one continuous thread.

Матеріали для цього кроку:

Моток вовняної пряжіМоток вовняної пряжі1 штука

Необхідні інструменти ({count})

Голка для нальбіндингуГолка для нальбіндингу
8

Shape the tube

Increase by working two stitches into one loop and decrease by skipping a loop, shaping the tube — narrowing for an ankle, turning a heel, or rounding a mitten — as the piece requires.

Необхідні інструменти ({count})

Голка для нальбіндингуГолка для нальбіндингу
9

Close the toe

At the end, decrease steadily until only a few loops remain, then pass the needle through them and draw them tight to close the toe or mitten tip.

Необхідні інструменти ({count})

Голка для нальбіндингуГолка для нальбіндингу
10

Secure and trim the tail

Weave the final yarn tail back through several stitches on the inside to lock it, then trim it flush. Because the fabric is looped, not knitted, it cannot unravel from the cut end.

Необхідні інструменти ({count})

Голка для нальбіндингуГолка для нальбіндингу
НожиціНожиці

Матеріали

1

Необхідні інструменти

2

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...