Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Crank-and-Link Double-Dasher Churn: Two Dashers' Cranks Joined by a Curved Link, One Lever Turns or Rocks Both
Buttercup

Створено

Buttercup

12. листопад 2026IE
7
0
0
0
0

Crank-and-Link Double-Dasher Churn: Two Dashers' Cranks Joined by a Curved Link, One Lever Turns or Rocks Both

Robert Parker of North Cohocton, New York, received US 33,213, dated 3 September 1861, for working two upright wing dashers in an oval churn with one lever. A cap that hooks onto ears on the box carries a horizontal crank over each dasher, coupled to its shaft. A curved link joins the two crank pins and the lever is pivoted to its middle: moving the lever's end round turns both dashers together, pushing it straight to and fro rocks them, and the user can work it from the front or the side. Unhook the cap and the whole mechanism lifts off. The patent gives no sizes; every size here is ours.
Середній
About 2 days

Інструкції

1

Turning or rocking with one lever

Завантаження блокнота Jupyter…
2

A mechanism that lifts off the churn as one, four months before

Stilwell swings his driving arm back on a frame. Parker's whole drive is in a cap that hooks onto ears and lifts off.
3

Read US 33,213

"The object of my invention is to so arrange the mechanism that by a rectilinear movement of the operator either a vibratory or rotary motion may be given to the dashers."
4

Oval box A, cover, cups and ears C

Make an oval box A whose inside is two 90 mm half rounds 140 mm apart joined by straight sides, 300 deep: a hardwood floor and two straight hardwood sides, with 1.5 mm stainless sheet bent round the ends in grooves, all sealed with silicone. Seal a printed cup for each dasher's foot on the floor at the half rounds' centres. Cut an HDPE cover to the outside with a 27 mm hole over each cup. Screw a hardwood ear C 30 x 60 mm, 140 long, to each end, standing above the box, with a mortise c 24 mm wide and 20 deep near its top.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини3 штук
Лист нержавкої сталіЛист нержавкої сталі1 штука
Силіконовий герметикСиліконовий герметик1 штука
Столярний клейСтолярний клей1 штука
Шурупи по деревуШурупи по дереву24 штук
Філамент PETGФіламент PETG1 штука
Лист ПЕВГЛист ПЕВГ1 штука

Необхідні інструменти ({count})

3D-принтер FDM3D-принтер FDM
Циркулярний верстатЦиркулярний верстат
ЕлектролобзикЕлектролобзик
КомпасКомпас
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Струбцина з напрямноюСтрубцина з напрямною
Набір викрутокНабір викруток
5

Print the cups (two)

A cup for a dasher's foot: 44 mm across, 14 high, a 26 mm socket 10 deep. Print two. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Файл дизайнуSTLCC0 - Free
6

Wing dashers B and shafts a

Turn two hardwood dasher shafts 25 mm across, 320 long, and set a 16 mm stainless rod 80 mm long 20 mm into each top, with a flat filed on its end as the tenon of the coupling f. Mortise four hardwood wings 120 x 120 x 12 mm through each, two crossed at 35 to 155 mm up and two crossed at 160 to 280, turned 45 degrees from the lower pair.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини1 штука
Пруток із нержавкої сталіПруток із нержавкої сталі2 штук
Столярний клейСтолярний клей1 штука
Шканти з твердої деревиниШканти з твердої деревини1 штука

Необхідні інструменти ({count})

Токарний верстат по деревуТокарний верстат по дереву
Циркулярний верстатЦиркулярний верстат
Набір стамесок по деревуНабір стамесок по дереву
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Напилки (ручний напилок)Напилки (ручний напилок)
7

Cap D, cranks e, link o and lever h

Glue up a hardwood cap D 400 x 120 x 60 mm, cut a recess d 260 x 100 mm, 42 deep, in its underside, and a slot through its front wall for the lever. Glue a tenon b 24 x 20 mm on each end to drop into the ears' mortises, and fit a hook and eye at each end to hold it. Bore it 16.6 mm through over each dasher. Make each crank e of a 16 mm stainless shaft through the cap with a slot in its foot to take the dasher's tenon (the coupling f), and a mild steel flat bar arm, 35 mm throw, with an 8 mm pin. Bend a 6 mm steel rod into a half round joining the two pins, eyes at its ends, and fix a pivot eye at its middle. Pivot a hardwood lever h, 500 long with a handle, on the eye so it comes out through the cap's slot.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини2 штук
Столярний клейСтолярний клей1 штука
Гачок і петляГачок і петля2 штук
Пруток із нержавкої сталіПруток із нержавкої сталі1 штука
Смуга з маловуглецевої сталіСмуга з маловуглецевої сталі1 штука
Круглий пруток з маловуглецевої сталіКруглий пруток з маловуглецевої сталі1 штука
Набір шестигранних болтівНабір шестигранних болтів3 штук
Самоконтрувальна гайка з нейлоновим кільцемСамоконтрувальна гайка з нейлоновим кільцем3 штук
ШплінтШплінт2 штук

Необхідні інструменти ({count})

Циркулярний верстатЦиркулярний верстат
Набір стамесок по деревуНабір стамесок по дереву
Ручний фрезерРучний фрезер
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Ножівка по металуНожівка по металу
Напилки (ручний напилок)Напилки (ручний напилок)
Слюсарні лещатаСлюсарні лещата
Набір викрутокНабір викруток
8

The build in 3D

FreeCAD model of this build, half the box cut away: the oval box with its cups and ears, the two wing dashers, the cap hooked onto the ears with the two cranks, the curved link and the lever coming out of its slot.
Файл дизайнуBLENDCC0 - Free
9

Churn

Stand the dashers in their cups, pour about 12 litres of heavy cream at about 15 °C, checked with the thermometer, into the box, put on the cover over the shafts, and lower the cap so the cranks' slots take the dashers' tenons and its tenons drop into the ears; hook it. Move the lever's end round in a small circle to turn the dashers, or push it straight to and fro to rock them, timing it. When the butter comes, unhook and lift off the cap, lift out the dashers, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Матеріали для цього кроку:

Жирні вершкиЖирні вершки12 l
Крупна морська сільКрупна морська сіль1 штука
ВодаВода1 штука

Необхідні інструменти ({count})

Термометр зі щупом, що лишається в стравіТермометр зі щупом, що лишається в страві
СекундомірСекундомір
Цифрові кухонні вагиЦифрові кухонні ваги
Велика миска з нержавкої сталіВелика миска з нержавкої сталі
10

Troubleshooting

Crank-link churn troubleshooting.

Flow

Loading...
11

History and honest limits

**Robert Parker** of North Cohocton, Steuben County, New York, US 33,213, 3 September 1861, "Improved Churn". He claimed "the combination of the cranks, the curved link, and the operating-lever". His box was oval and staved; ours has straight sides and stainless ends. He does not describe the dashers beyond "wing-dashers"; ours follow his Fig. 1. The patent gives no sizes; every size here is ours.

Матеріали

18

Необхідні інструменти

18

Файли дизайну

2

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...