Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Adjustable-Dish Churn: Cream Is Poured Between a Fixed Ribbed Dish and a Turning One, Then Beaten by Wings and Dashers
Buttercup

Створено

Buttercup

11. листопад 2026IE
9
0
0
0
0

Adjustable-Dish Churn: Cream Is Poured Between a Fixed Ribbed Dish and a Turning One, Then Beaten by Wings and Dashers

John Pike of Syracuse, New York, received US 30,930, dated 18 December 1860, for a box churn with a cranked shaft of dashers. At its far end a fixed concave dish with broken radial ribs faces a turning dish with ribs and a ring that runs through the breaks. Cream poured into a pan on top runs down a passage and through a slot between the two dishes, where it is beaten and partly ground, then flung out to wings and dashers in the box. Two thumb screws set the turning dish farther off for cream or closer for milk. The fixed dish is the patent's eight inches across; every other size here is ours.
Просунутий
About 3 days

Інструкції

1

Setting the gap between the dishes

Завантаження блокнота Jupyter…
2

Cream worked between a fixed and a turning face, two years before

Brown forces cream out between corrugated rings. Pike pours it between a fixed and a turning ribbed dish whose gap he can set.
3

Read US 30,930

"By this arrangement the concavo-convex dish E can be adjusted to a greater or less distance from the concave dish D; fixing the two dishes farther apart when churning cream, shown by the red lines in Fig. 1, and close together when churning milk."
4

Box A, lid and conduit p

Glue up hardwood for a box A 400 mm long, 260 wide and 280 high inside: a fixed end 40 mm thick and 322 tall, a crank end 22 thick, sides and floor 22 thick, joints sealed with silicone sealant, and a loose lid with a knob covering all but the fixed end. Bore the fixed end 16 mm straight down from its top, 20 mm in from its outside face, to 82 mm above the shaft's centre (which is 140 mm above the floor), and bore 16 mm in from its inside face to meet it: the conduit p. Set a kitchen funnel in the top of it as the pan B. Bore the fixed end 12.8 mm at the shaft's centre for the rod u and the crank end 16.6 mm.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини4 штук
Столярний клейСтолярний клей1 штука
Силіконовий герметикСиліконовий герметик1 штука
Шурупи по деревуШурупи по дереву30 штук
Кухонна лійкаКухонна лійка1 штука

Необхідні інструменти ({count})

Циркулярний верстатЦиркулярний верстат
Ручний фрезерРучний фрезер
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Набір перових сверделНабір перових свердел
Струбцина з напрямноюСтрубцина з напрямною
Набір викрутокНабір викруток
РулеткаРулетка
5

Print the fixed dish D

The fixed dish D: 203 mm across (the patent's eight inches), its face dished at 12 degrees, eight radial ribs h 6 mm high broken from 46 to 64 mm out, a rim flange m, a 12.8 mm centre opening e and a 20 x 25 mm slot f at the top. Needs a 220 mm bed. PETG, 0.2 mm layers, 30 % infill, 4 walls, printed on its back with supports.
Файл дизайнуSTLCC0 - Free
6

Print the turning dish E

The turning dish E: 180 mm across, 5 mm thick, dished at 12 degrees, six ribs 6 mm high on its convex face, a ring t 52 to 58 mm out standing 12 mm, a boss for the rod u, and the sawcalf tab i on its concave face. PETG, 0.2 mm layers, 30 % infill, 4 walls, printed on its back with supports.
Файл дизайнуSTLCC0 - Free
7

Dishes D and E, wings d, rod u and thumb screws

Screw the dish D to the inside of the fixed end, its slot f over the conduit p, sealing round it. Cut six hardwood wings d 34 x 94 x 4 mm and screw them radially to the concave face of E so they reach 120 mm from the centre. Thread a 12 mm stainless rod u 120 mm long at one end for 70 mm and fix its plain end into E's boss with sealant and a cross pin. Pass it through D and the fixed end. Screw a mild steel flat bar plate q outside, bored 12.8 mm, and run a wing nut and washer on the thread either side of it: the thumb screws s and v.

Матеріали для цього кроку:

Філамент PETGФіламент PETG1 штука
Силіконовий герметикСиліконовий герметик1 штука
Шурупи по деревуШурупи по дереву18 штук
Дошка з твердої деревиниДошка з твердої деревини1 штука
Пруток із нержавкої сталіПруток із нержавкої сталі1 штука
Смуга з маловуглецевої сталіСмуга з маловуглецевої сталі1 штука
Гайка-баранецьГайка-баранець2 штук
Плоска шайбаПлоска шайба2 штук

Необхідні інструменти ({count})

3D-принтер FDM3D-принтер FDM
Ножівка по металуНожівка по металу
Напилки (ручний напилок)Напилки (ручний напилок)
Слюсарні лещатаСлюсарні лещата
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Розвідний ключРозвідний ключ
Набір викрутокНабір викруток
8

Shaft C, dashers x, cog shaft w and crank m

Cut a hardwood shaft C 32 mm square and 340 mm long. Saw a slot 7 x 22 mm, 15 deep, across one end to take the sawcalf tab, and chisel a 16.4 mm square socket 50 deep in the other, so C can slide 15 mm as E is set. Mortise six hardwood paddles x 25 x 6 mm through it, 40 mm apart, alternately up and down, reaching 110 mm from its centre. File the end of a 16 mm stainless cog shaft w 110 mm long square for 34 mm; pass it through a hardwood bearing block on the crank end into the socket and pin a crank m of mild steel flat bar, 120 mm throw, with a hardwood handle, on its outer end. Set C's slot over the tab and hold it with a split pin through both.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини1 штука
Столярний клейСтолярний клей1 штука
Пруток із нержавкої сталіПруток із нержавкої сталі1 штука
Смуга з маловуглецевої сталіСмуга з маловуглецевої сталі1 штука
Шканти з твердої деревиниШканти з твердої деревини1 штука
ШплінтШплінт2 штук
Шурупи по деревуШурупи по дереву4 штук

Необхідні інструменти ({count})

Циркулярний верстатЦиркулярний верстат
Набір стамесок по деревуНабір стамесок по дереву
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Ножівка по металуНожівка по металу
Напилки (ручний напилок)Напилки (ручний напилок)
Слюсарні лещатаСлюсарні лещата
9

The build in 3D

FreeCAD model of this build, the near side cut away: the box with its bored fixed end and funnel, the fixed ribbed dish, the turning dish with its ring and wings, the rod with its thumb screws on the plate, the shaft with six paddles, and the cog shaft and crank.
Файл дизайнуBLENDCC0 - Free
10

Set the gap and churn

For cream, set the turning dish's face 30 mm from the fixed dish's face with the thumb screws (closer, 15 mm, is Pike's setting for milk). Turn the crank briskly and, while it turns, pour about 8 litres of heavy cream at about 15 °C, checked with the thermometer, into the funnel, timing it. When the butter comes, lift the lid, pull the split pin and lift out the shaft C, take out the butter, drain the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Матеріали для цього кроку:

Жирні вершкиЖирні вершки8 l
Крупна морська сільКрупна морська сіль1 штука
ВодаВода1 штука

Необхідні інструменти ({count})

Термометр зі щупом, що лишається в стравіТермометр зі щупом, що лишається в страві
СекундомірСекундомір
Цифрові кухонні вагиЦифрові кухонні ваги
Велика миска з нержавкої сталіВелика миска з нержавкої сталі
Розвідний ключРозвідний ключ
11

Troubleshooting

Adjustable-dish churn troubleshooting.

Flow

Loading...
12

History and honest limits

**John Pike** of Syracuse, Onondaga County, New York, US 30,930, 18 December 1860, "Churn". He claimed "the combination and arrangement of the adjustable convex dish D, concavo convex dish E, with the radial beaters on each as described, together with the wings d, d, shaft C, and dashers x, x". He wrote that the butter comes "ordinarily inside of two minutes with sweet milk and one minute with cream"; we have not tested that. His pan B was metal, his dish D adjustable on a slide H and his shaft held to E by a spring c; ours is a kitchen funnel, a dish screwed fast and a split pin. Neither the text nor the drawing gives the gearing's form; ours is a plain crank. His D is "say eight inches in diameter", which we use; every other size here is ours.

Матеріали

15

Необхідні інструменти

18

Файли дизайну

3

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...