Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Razor Blades from a Continuous Steel Strip (Tarbox 1915)
J. P. Tarbox · Public domain (US patent)
Forge

Створено

Forge

27. жовтень 2026NO
15
0
0
0
0

Razor Blades from a Continuous Steel Strip (Tarbox 1915)

Safety razor blades are made without ever cutting the steel into loose pieces first. A long strip, blade-wide and blade-thick, is punched and notched at every blade length. It then runs through grinding, hardening, tempering, edge grinding, stropping and wrapping, and only at the end is it snapped apart into blades. John Tarbox's machine even set the temper itself, with a selenium cell that watched the colour of the steel. Source: J. P. Tarbox, US 1,165,037 (1915). The patent gives no temperatures, steel grade or blade sizes. Picture: Tarbox's drawing of the whole line.
Просунутий
Continuous line

Інструкції

1

Punch and weaken the strip

Start from steel rolled into long strip as wide and as thick as the blade. Punch holes along it to suit the razor holder: a Gillette-type holder has three projections. At every blade length, weaken the strip by notching both edges, thinning it across, or punching a hole on the line.

Матеріали для цього кроку:

Стрічка з вуглецевої сталіСтрічка з вуглецевої сталі1 strip

Необхідні інструменти ({count})

Штампувальний пресШтампувальний прес
2

Rough-grind the faces

Feed the strip by its holes between a pair of grinding wheels, one on each side, to remove the surface irregularities.

Необхідні інструменти ({count})

Шліфувальний кругШліфувальний круг
3

Harden: heat and chill

Run it through an electric tunnel heater, then straight into a chilling bath of oil or water.

Необхідні інструменти ({count})

Трубчаста пічТрубчаста піч
Гартівна ванна з оливоюГартівна ванна з оливою
4

Rub off the oxide

Pass it between emery wheels to rub the oxide off the chilled strip, so its temper colour can be seen when it is reheated.

Необхідні інструменти ({count})

Шліфувальний кругШліфувальний круг
5

Temper to straw colour

Reheat it in a second, smaller tunnel heater and chill it again. Tarbox held the colour at the temper wanted, for example straw, by letting a selenium cell compare the strip with a coloured standard disk and adjust the heater.

Необхідні інструменти ({count})

Трубчаста пічТрубчаста піч
Гартівна ванна з оливоюГартівна ванна з оливою
6

Grind and strop the edges

Grind both edges at once between four grinding wheels, hone if wanted, then pass the strip between strop wheels faced with stropping material.

Необхідні інструменти ({count})

Шліфувальний кругШліфувальний круг
Шкіряний ремінь для правкиШкіряний ремінь для правки
7

Wrap, break apart and pack

Wrap the strip spirally in paraffined paper. Then snap it at each weakened line over notched wheels, alternately from each side, and count and pack the blades.

Необхідні інструменти ({count})

Вощений папірВощений папір

Матеріали

1

Необхідні інструменти

6

За цим кресленням виготовляють

Пов'язані креслення

Ці креслення діляться знаннями — техніки, матеріали або принципи

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...