Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Reverberatory Furnace: the Air Furnace for Melting Cast Iron (Bolland, 1893)
Forge

Створено

Forge

4. листопад 2026NO
13
0
0
0
0

Reverberatory Furnace: the Air Furnace for Melting Cast Iron (Bolland, 1893)

An air furnace melts iron apart from the fuel: coal burns on a grate at one end, and the flame is thrown down from a low arched roof onto the iron on the bed, then leaves by a tall chimney. The iron stays cleaner than in a cupola, so founders used it for guns, rolls, heavy scrap and lumps too big for the cupola. This furnace is 30 ft 6 in long and 7 ft wide outside, 5 ft wide inside, cased in bolted wrought-iron plates. Source: S. Bolland, The Iron Founder Supplement (1893), pp. 55-67. Unknown: brick sizes, plate thickness. Picture: Fig. 14 of the book.
Експерт
Unknown

Інструкції

1

Lay the foundation

Build the foundation solid of common material up to the firebrick, shaped so the firebrick bed slopes down from the chimney end to the reservoir. Keep the bricks from B to C 6 in below the finished bottom, to leave room for the sand bed.

Матеріали для цього кроку:

ЦеглаЦегла1 foundation

Необхідні інструменти ({count})

КельмаКельма
Невідомі розміриНевідомі розміри
2

Build the fireplace, bridge and roof

Build the fireplace the full width of the furnace (5 ft inside, grate 5 ft long). Set the bridge wall at least 2 ft 3 in from the face of the grate bars. Build bridge, sides, roof and fireplace of the most refractory firebrick. Arch the roof the whole length, low, so it throws the flame down onto the bed; fill above the arches with common material. Leave the side charging hole (5 x 4 ft), the top hole (furnace width x 6 ft), the puddling hole over the reservoir, a sight hole and the tap hole.

Матеріали для цього кроку:

Шамотна цеглаШамотна цегла1 lining, bridge, roof
Розчин із вогнетривкої глиниРозчин із вогнетривкої глини1 setting
ЦеглаЦегла1 filling above the arch
Невідомий металНевідомий метал1 grate bars

Необхідні інструменти ({count})

КельмаКельма
3

Case it in plates and bolt it

Case the whole structure in wrought-iron plates, held at the corners with angle-irons. Run eight chief anchor bolts from side to side, clear of all working parts. Join everything with bolts, not rivets, so any plate can come off for repairs. Line the charging doors with firebrick.

Матеріали для цього кроку:

Залізна плитаЗалізна плита1 casing, doors
Пруток із кованого залізаПруток із кованого заліза8 anchor bolts
Невідомий металНевідомий метал1 angle-irons, door frames
Шамотна цеглаШамотна цегла1 door linings

Необхідні інструменти ({count})

Невідомі розміриНевідомі розміри
4

Build the chimney

Build the chimney square, 30 to 40 ft high, with an inside course of firebrick (Fig. 14: 2 ft 6 in square inside). Make its area a little larger than the fireplace. Put a damper on top that can be worked from the bottom: it alone sets the draught. It can stand apart on a sole plate on four columns.

Матеріали для цього кроку:

Шамотна цеглаШамотна цегла1 inside course
ЦеглаЦегла1 chimney
Невідомий металНевідомий метал1 damper

Необхідні інструменти ({count})

КельмаКельма
5

Make the sand bottom

Make the bottom from B round the reservoir to C with 8 parts fire-sand to 1 of clay and 1 of ground coke. Fire it well for one to two hours before the first charge; it should last ten heats. Fill the tap hole with fire-sand and a little coal dust, which will not cake when hot.

Матеріали для цього кроку:

ПісокПісок8 parts
ГлинаГлина1 part
Металургійний коксМеталургійний кокс1 part, ground

Необхідні інструменти ({count})

Кам'яне вугілля бітумінознеКам'яне вугілля бітумінозне
6

Charge and melt

Fire with soft, non-caking bituminous coal and keep a full grate; clinker quickly and leave no holes for cold air. Charge all the iron at the start: first layer of pigs lengthwise and a little apart, next layers across, open so the flame passes. Set heavy pieces on firebricks so the flame plays all round them. Through the puddling hole, dip test pieces and skim the iron clean. To blend two grades, thrust green saplings into the melt. Close the damper before tapping. Look the furnace over after every heat.

Необхідні інструменти ({count})

Кам'яне вугілля бітумінознеКам'яне вугілля бітумінозне
Чушки чавунуЧушки чавуну
Жердина з молодої твердої деревиниЖердина з молодої твердої деревини
Дірчаста шумівкаДірчаста шумівка

Матеріали

9

Необхідні інструменти

6

За цим кресленням виготовляють

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...