Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Ore Crushing Rolls: Hard Shells on Soft Iron Cores, One Roll in Spring-Loaded Boxes, Gap Set by Shims (Richards, Ore Dressing, 1903)
Forge

Створено

Forge

15. листопад 2026NO
2
0
0
0
0

Ore Crushing Rolls: Hard Shells on Soft Iron Cores, One Roll in Spring-Loaded Boxes, Gap Set by Shims (Richards, Ore Dressing, 1903)

The crushing rolls that took ore from the jaw breaker in a 1900s mill, as Robert Richards described them: two shafts on one cast-iron frame, each carrying a soft-iron core with a replaceable hard shell; one runs in fixed boxes, the other in movable boxes pushed toward it by a nest of steel springs that yields like a safety valve; shims set the gap. Little fines, ideal for soft brittle ores.
Просунутий
Weeks (castings and machining)

Інструкції

1

His figures

Завантаження блокнота Jupyter…
2

Read Richards

"The ore is therefore broken by compression."
3

Frame and shafts

Cast the frame as one piece, both sides joined by end pieces, so settling of the building can't throw the shafts out of line (make it in two parts only if it must travel by mule). Turn two shafts of mild steel or wrought iron, each on two bearings.

Матеріали для цього кроку:

Чавунні виливкиЧавунні виливки1 штука
Сталевий валСталевий вал1 штука

Необхідні інструменти ({count})

Ливарний ківшЛиварний ківш
Токарний верстат по металуТокарний верстат по металу
ПоліспастПоліспаст
4

Cores and shells

Force a soft cast-iron core onto each shaft. Krom's way (Fig. 37): two slightly conical half-cores, one shrunk on for good, the other split on one side and drawn in by four draw bolts; half-cores no wider than 4-5 in. Cast hard shells 2-5½ in. thick (chilled iron or steel), with wrought-iron staves cast in if chilled so the slightly conical inside can be turned to fit; turn the face true.

Матеріали для цього кроку:

Чавунні виливкиЧавунні виливки1 штука
Пруток кованого залізаПруток кованого заліза1 штука
Набір шестигранних болтівНабір шестигранних болтів1 штука

Необхідні інструменти ({count})

Токарний верстат по металуТокарний верстат по металу
Ливарний ківшЛиварний ківш
5

Boxes, springs and shims

Mount one shaft in fixed boxes and the other in movable ones, both babbitted, with shields and a cotton-waste groove against grit. Put a nest of steel spiral springs outside the fixed pillow block, with bolts carrying the force to the movable box, equal on both sides, compressed between plates by two compression bolts. Set the gap with shims and keep them in: the springs should only give when a hard lump comes through.

Матеріали для цього кроку:

Coil SpringCoil Spring1 штука
Невідомий металНевідомий метал1 штука
Набір шестигранних болтівНабір шестигранних болтів1 штука
Чавунні виливкиЧавунні виливки1 штука

Необхідні інструменти ({count})

Набір гайкових ключівНабір гайкових ключів
Токарний верстат по металуТокарний верстат по металу
6

Drive and run

Drive by belt and pulley (or gears and pulleys for slow coarse work). Feed lumps no bigger than about 1½ in. (4 cm), 2½ in. at most, evenly with a feeder so a rush of ore does not choke it.

Матеріали для цього кроку:

БлокБлок1 штука
Приводний пасПриводний пас1 штука

Необхідні інструменти ({count})

Набір гайкових ключівНабір гайкових ключів
7

Troubleshooting

Crushing rolls troubleshooting.

Flow

Loading...
8

History and honest limits

From Robert H. Richards, *Ore Dressing* vol. I (1903), Chapter III, §§ 71-85, pp. 62-74, Fig. 37 and Tables 34-39 (checked on the archive.org scan oredressing01richuoft; p. 62 from its text layer). Rubber springs were the cheap short-life option; levers and weights had nearly gone out of use. Richards surveys machines from many makers rather than one design: building from castings, the size and metric are ours, and the babbitt alloy has no head yet.

Матеріали

8

Необхідні інструменти

4

За цим кресленням виготовляють

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...