Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Garden Hand Plow From Scrap: Wheelbarrow Wheel, Ripped Spruce Handles and a Shovel-Blade Moldboard (Boy Mechanic, 1919)
Forge

Створено

Forge

13. листопад 2026NO
8
0
0
0
0

Garden Hand Plow From Scrap: Wheelbarrow Wheel, Ripped Spruce Handles and a Shovel-Blade Moldboard (Boy Mechanic, 1919)

T. T. Sturgeon's hand plow from The Boy Mechanic, Book 3 (1919), "worth about $5 at an outlay of 25 cents": a 16 in wheelbarrow wheel, handles ripped from one spruce strip, iron-strap braces, an adjustable vertical strap, and a moldboard and share cut from an old shovel blade to his grid pattern.
Середній
About 1 day

Інструкції

1

His cut list in centimetres

Завантаження блокнота Jupyter…
2

Read The Boy Mechanic, Book 3

"The labor of spading a garden of even moderate size is sufficient to warrant the person who undertakes the job in making a hand plow like that shown in the illustration."
3

Make the handles

Mark both handles on a 7/8 by 4 in spruce strip 5 ft long, one curved grip at each end on opposite edges. Cut the curves with a keyhole saw, then rip the board into the two handles; smooth them and trim the grips with a sharp knife. Cut a section of broomstick for the upper brace.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини1 штука
МітлаМітла1 штука

Необхідні інструменти ({count})

Лобзикова пилкаЛобзикова пилка
Ножівка для поздовжнього пилянняНожівка для поздовжнього пиляння
Ніж для шкіриНіж для шкіри
ОлівецьОлівець
4

Make the iron parts

Lower brace: iron 1/4 by 1-1/4 by 12 in, drilled for 1/4 in bolts, bent at right angles 1-1/2 in from each end, with a 1/4 in hole at the middle. Vertical support: 1/4 by 1-1/4 by 18 in, four 1/4 in adjusting holes 1 in apart at the top, three 1/4 in holes at the bottom for the moldboard, and a 5/16 in hole at the 7-1/2 in mark. Two braces 14 in long of 1/4 by 1-1/4 in, a 3/8 in hole at the front of each for the 3/8 by 10 in axle bolt and a 5/16 in hole at the other end, each 1 in from the end. Landside: 1/8 by 3/4 by 12 in.

Матеріали для цього кроку:

Смуга з маловуглецевої сталіСмуга з маловуглецевої сталі3 штук

Необхідні інструменти ({count})

Ножівка по металуНожівка по металу
Ручний дрильРучний дриль
Слюсарні лещатаСлюсарні лещата
МолотокМолоток
Напилки (ручний напилок)Напилки (ручний напилок)
РулеткаРулетка
5

Cut the moldboard

Draw his moldboard (Fig. 4) on cardboard ruled in 1 in squares, tracing the outline square by square, and mark the bolt holes. Trace it on an old shovel blade, using the thickest part for the point of the share. Cut it out, smooth the edges and sharpen the cutting edge. Drill for 1/4 in bolts to the vertical strap and 3/16 in bolts to the landside.

Матеріали для цього кроку:

ЛопатаЛопата1 штука
Картонні аркуші для шаблонівКартонні аркуші для шаблонів1 штука

Необхідні інструменти ({count})

ОлівецьОлівець
Ножівка по металуНожівка по металу
Кутова шліфмашинаКутова шліфмашина
Напилки (ручний напилок)Напилки (ручний напилок)
Ручний дрильРучний дриль
6

Shape and assemble

Curve the moldboard and fit it to the supports as in Figs. 1-3. Bend the 12 in landside strip under the moldboard and bolt it on. Assemble on the 16 in wheel and 3/8 in axle bolt, with wheel and landside in line (Fig. 2) and the landside's rear edge raised slightly (Fig. 3); set the vertical strap's height for the operator in its adjusting holes. Paint the plow and oil the smoothed cutting parts.

Матеріали для цього кроку:

Колесо тачкиКолесо тачки1 штука
Болт із півкруглою головкоюБолт із півкруглою головкою6 штук
Шестигранна гайкаШестигранна гайка6 штук
Плоска шайбаПлоска шайба6 штук
Олійна фарбаОлійна фарба1 штука
Машинне мастилоМашинне мастило1 штука

Необхідні інструменти ({count})

Слюсарні лещатаСлюсарні лещата
МолотокМолоток
Широкий малярний пензельШирокий малярний пензель
7

Troubleshooting

Garden plow troubleshooting.

Flow

Loading...
8

History and honest limits

From "Garden Plow Made of Pick-Up Material" by T. T. Sturgeon, in **The Boy Mechanic, Book 3**, Popular Mechanics, 1919 (Project Gutenberg 71856; checked on the archive.org scan boymechanic0003unse, pp. 227-228). The moldboard shape is his Fig. 4 grid. The keyhole saw is a coping saw here; the tools and metric figures are ours.

Матеріали

11

Необхідні інструменти

12

За цим кресленням виготовляють

Пов'язані креслення

Ці креслення діляться знаннями — техніки, матеріали або принципи

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...