Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО

Teapot: a Tinplate Picnic Teapot with Cock and Strainer (Hasluck, 1907)
A square tinplate teapot from a picnic outfit: folded from one blank, with a hinged lid, and a cock at the bottom behind a perforated strainer that holds back the leaves.
Blank 1 ft 4 1/4 in by 1 ft 0 3/8 in; lid 4 1/8 by 4 in.
Source: Paul N. Hasluck, Tinplate Work (1907), pp. 37-39. Unknown: folding order, solder, the cock. Picture: Figs. 96-97 of the book.
Середній
Unknown
Інструкції
1
1
Cut the body blank
Cut the body blank
Cut a piece of tin 1 ft 4 1/4 in long by 1 ft 0 3/8 in wide and mark the pattern of Fig. 96 on it, with the hole for the cock tube. Not given: the folding order. Ours: bend it up on the dotted lines and solder the seams.
Матеріали для цього кроку:
Лист білої жерсті1 body
Олов'яно-свинцевий припій1 штукаНеобхідні інструменти ({count})
Рисувалка
Ножиці по металу
Кілок
Дерев'яний молоток (киянка)
Електричний паяльник
Флюс2
2
Fit the cock and strainer
Fit the cock and strainer
Solder a tube about 1/2 in long into the hole for the cock (Fig. 97) and fit the cock to it. Develop the strainer (Fig. 98): top curve radius 1 13/16 in, chord corner to corner 2 15/16 in. Perforate it and solder it across the corner in front of the tube (Fig. 99).
Матеріали для цього кроку:
Латунна трубка1 1/2 in
Зливний кран1 штука
Лист білої жерсті1 strainer
Олов'яно-свинцевий припій1 штукаНеобхідні інструменти ({count})
Розмічальний циркуль
Ножиці по металу
Просічка для листового металу
Брусок твердої деревини
Електричний паяльник
Флюс3
3
Make the hinged lid
Make the hinged lid
Cut the lid (Fig. 100) 4 1/8 by 4 in; the inner rectangle 3 1/2 by 3 1/2 in leaves 1/4 in to bend up. Cut hinge projections 1/2 in wide by 5/8 in deep with equal spaces, the outer ones only 1/4 in wide. Bend them round a wire 1/16 in thick. Hasluck adds that the teapot may be enamelled dark green.
Матеріали для цього кроку:
Лист білої жерсті1 lid
Залізний дріт1 1/16 inНеобхідні інструменти ({count})
Ножиці по металу
Кілок
Дерев'яний молоток (киянка)Матеріали
5- 1 lidЗаповнювач
- Заповнювач
- 1 1/2 inЗаповнювач
- 1 штукаЗаповнювач
- 1 1/16 inЗаповнювач
Матеріали з пов'язаних креслень
За цим кресленням виготовляють
CC0 Суспільне надбання
Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.
Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.


