Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Double-Ended Scriber from a Worn Saw File: Annealed in Lime, Filed Round in a Grooved Block, Points Hardened (Thompson, Amateur Work)
Forge

Створено

Forge

14. листопад 2026NO
7
0
0
0
0

Double-Ended Scriber from a Worn Saw File: Annealed in Lime, Filed Round in a Grooved Block, Points Hardened (Thompson, Amateur Work)

The marking scriber Richard Thompson made for his surface gauge in Amateur Work: 1/8 in. steel or a worn-out saw file, drilled in the middle, pointed at both ends with one end bent, annealed by burying it red-hot in lime, filed round while turned in a grooved hardwood block, and the points hardened.
Початківець
Two hours

Інструкції

1

Read Thompson

"A worn-out saw file will answer very well, with a hole drilled through the centre to fit the bolt and pointed at each end, one of which is bent."
2

Rough the shape

Forge a flat piece of steel about 1/8 in. (3 mm) thick, or a worn-out saw file, roughly to shape: pointed at both ends, one end bent into a short hook (his fig. 30).

Матеріали для цього кроку:

Смуга інструментальної сталіСмуга інструментальної сталі1 штука

Необхідні інструменти ({count})

Кувальне горноКувальне горно
КовадлоКовадло
МолотокМолоток
Ковальські кліщіКовальські кліщі
3

Anneal in lime

Heat it gently to a dull red and bury it in lime to cool slowly: it is then easy to file.

Матеріали для цього кроку:

Гашене вапно (гідроксид кальцію)Гашене вапно (гідроксид кальцію)1 штука

Необхідні інструменти ({count})

Кувальне горноКувальне горно
Ковальські кліщіКовальські кліщі
4

Drill and flatten

Drill a hole through the middle to fit the mounting bolt and file the flat part to an even thickness for about 1/2 in. each side of the hole.

Необхідні інструменти ({count})

Свердлильний верстатСвердлильний верстат
Слюсарні лещатаСлюсарні лещата
Напилки (ручний напилок)Напилки (ручний напилок)
5

File it round

Cut a groove along the end of a hardwood block about 3 x 2 x 1/2 in., held end up in the vice. Lay the scriber in the groove, turn it slowly toward you with the left hand and file it round with the right. File the points quite sharp.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини1 штука

Необхідні інструменти ({count})

Ручна пилкаРучна пилка
Слюсарні лещатаСлюсарні лещата
Напилки (ручний напилок)Напилки (ручний напилок)
6

Harden the points

Harden the points (he gives no method; ours: heat the tips to a bright red and quench in water), then touch them up on an oilstone.

Необхідні інструменти ({count})

Кувальне горноКувальне горно
Гартівна діжкаГартівна діжка
Точильний брусокТочильний брусок
7

Troubleshooting

Scriber troubleshooting.

Flow

Loading...
8

History and honest limits

From Richard Thompson, "How to Construct a Compound Microscope" III, **Amateur Work, Illustrated**, vol. III, p. 198 and fig. 30 (checked on the archive.org scan amateurworkillus03lond). He mounts the scriber on a mahogany surface gauge with three brass washers 3/4 in. across and 1/16 in. thick. The hardening method, metric figures and tools are ours.

Матеріали

3

Необхідні інструменти

10

За цим кресленням виготовляють

Пов'язані креслення

Ці креслення діляться знаннями — техніки, матеріали або принципи

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...