Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО

Thompson (Nlaka'pamux) Smoked Buckskin: Scraped on a Leaning Poplar Log with a Deer Ulna, Soap-Soaked, Wrung, Pounded Soft, Smoked (Teit, 1900)
The Thompson (Nlaka'pamux) buckskin James Teit saw made around 1900: a soaked hide scraped on a peeled poplar log leaning against a tree with a deer's ulna or a horse rib used like a draw-knife, smoked over a small pit of smouldering rotten wood, soaked a day in soapy water, wrung with dry grass on a log and stick, pounded soft on a frame and smoked again.
Просунутий
About a week
Інструкції
1
1
Read Teit
Read Teit
"It is said that, after being smoked, the skin does not shrink so much when it gets wet as it otherwise would."
2
2
Soak and set up the log
Soak and set up the log
Soak the dry skin in water for several days. Peel a poplar log about 5 in. (13 cm) thick and 4 ft (1.2 m) long; stand one end on the ground and lean the other against a tree, in a notch cut in its bark.
Матеріали для цього кроку:
Сириця1 штука
Вода1 штука
Жердини із сирої деревини1 штукаНеобхідні інструменти ({count})
Міздрильна колода3
3
Scrape both sides
Scrape both sides
Lay the skin loosely over the log with some hanging over the top so the pressure holds it. Scrape the flesh side with a slightly sharpened deer ulna or horse rib held at both ends like a draw-knife, moving the skin as you go; then the hair side, taking the dark outer skin off with the hair. Bone cuts the skin less than iron.
Необхідні інструменти ({count})
Міздрильний ніж
Міздрильна колода4
4
Dry and smoke
Dry and smoke
Hang it over a pole to dry. Dig a hole about 1½ ft (45 cm) deep and a little over 1 ft (30 cm) across, light a smouldering fire of rotten fir wood (fir bark with dry pine cones is best; juniper for a very dark colour), set a frame of bent sticks over it, spread the skin on it and cover all with an old blanket. Turn it to smoke the other side.
Матеріали для цього кроку:
Гниле дерево1 штука
Вербовий прут1 штукаНеобхідні інструменти ({count})
Лопата
Вогнище
Парусина
Дерев'яна жердина5
5
Soap, wring and pound
Soap, wring and pound
Soak it 24 hours or more in warm water with a strong soap solution. Roll it lengthwise with a little dry grass, tie one end to a log with a rope, fold the other round a short stout stick and turn until the water is wrung out. Stretch it on a frame and pound the inside until quite dry and soft (warm it by a fire in cold weather), then smoke it again.
Матеріали для цього кроку:
Мило1 штука
Вода1 штука
Сіно1 штукаНеобхідні інструменти ({count})
Великий котел для фарбування
Канат
Дерев'яна лопать
Дерев'яна жердина6
6
Troubleshooting
Troubleshooting
Smoked buckskin troubleshooting.
Flow
Loading...
7
7
History and honest limits
History and honest limits
From James Teit, *The Thompson Indians of British Columbia*, **Memoirs of the American Museum of Natural History, Jesup North Pacific Expedition** vol. I part IV (1900), pp. 185-186 and Figs. 127-129 (checked on the archive.org scan cihm_16242). Some said smoking came from the Okanagon; many held that a skin rubbed with brains needs no smoking (see the Navajo brain-tan blueprint). Corncob smoke gave a bright yellow. Frame size and hay for the dry grass are ours.
Матеріали
7- 1 штукаЗаповнювач
- 2 штукЗаповнювач
- 1 штукаЗаповнювач
- 1 штукаЗаповнювач
- 1 штукаЗаповнювач
- 1 штукаЗаповнювач
- 1 штукаЗаповнювач
За цим кресленням виготовляють
Пов'язані креслення
Ці креслення діляться знаннями — техніки, матеріали або принципи

Navajo Buckskin: Hair Shaved with the Deer's Own Foreleg Bone, Brains Rubbed In, Wrung on a Tree, Worked Dry over the Feet (Shufeldt, 1888)
від Tex
Текстиль і шкіра
4
0
0
0
0
0

Blackfoot Sinew Thread: Dried Leg and Neck Sinew Shredded, Softened and Rolled Between the Palms (Wissler, 1910)
від Tex
Текстиль і шкіра
4
0
0
0
0
0
CC0 Суспільне надбання
Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.
Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.
