Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Watering Can: the Tinplate Rose Watering-Can (Hasluck, 1907)
Forge

Створено

Forge

4. листопад 2026NO
8
0
0
1
0

Watering Can: the Tinplate Rose Watering-Can (Hasluck, 1907)

A tinsmith's garden watering can: a round body from one sheet 2 ft 1 in x 8 1/2 in, a two-piece spout with a perforated rose, a hollowed top with a cross handle, and a back handle with a thumb ring. Tinplate or galvanised iron. Variable: the rose. Its pattern diameter is the rose diameter x 4 / 3; finer holes for seedlings. Source: Paul N. Hasluck, Tinplate Work (1907), pp. 54-57. Unknown: solder. Picture: Figs. 132-135 of the book.
Середній
Unknown

Інструкції

1

Make the body and bottom

Cut a sheet 2 ft 1 in by 8 1/2 in. Wire one edge, sink it in the crease iron, round it and groove the seam; solder the seam inside. Cut the spout hole opposite the seam, 2 1/2 in from the bottom. Edge the bottom to fit, beat it up and solder it from inside.

Матеріали для цього кроку:

Лист білої жерстіЛист білої жерсті1 body, bottom
Залізний дрітЗалізний дріт1 edge
Олов'яно-свинцевий припійОлов'яно-свинцевий припій1 штука

Необхідні інструменти ({count})

Ножиці по металуНожиці по металу
КілокКілок
Дерев'яний молоток (киянка)Дерев'яний молоток (киянка)
Електричний паяльникЕлектричний паяльник
ФлюсФлюс
2

Make and fit the spout

Cut the spout in two pieces (Fig. 133), bend them to shape and solder the seams. Solder the larger piece into the body. Make it longer for plants out of reach, with an elbow for plants up high. Make the stay: a taper strip as long as the gap between can and spout, bent to a half-round section and soldered in.

Матеріали для цього кроку:

Лист білої жерстіЛист білої жерсті1 spout, stay
Олов'яно-свинцевий припійОлов'яно-свинцевий припій1 штука

Необхідні інструменти ({count})

Ножиці по металуНожиці по металу
КілокКілок
Електричний паяльникЕлектричний паяльник
ФлюсФлюс
3

Make the rose

Set out the rose body (Fig. 135): its diameter is the rose diameter x 4 / 3, so a 3 in rose needs a 4 in pattern, with lines a b at right angles. Bend it over a funnel stake and solder the seam. Hollow a disc for the front, with edges for capping on. Inside the hollow, mark circles and pierce them at intervals with a bradawl over a hard wood block; very fine for seedlings. Solder front and stem to the rose body. Several roses of different sizes are useful.

Матеріали для цього кроку:

Лист білої жерстіЛист білої жерсті1 rose
Олов'яно-свинцевий припійОлов'яно-свинцевий припій1 штука

Необхідні інструменти ({count})

Розмічальний циркульРозмічальний циркуль
Ножиці по металуНожиці по металу
КілокКілок
Рихтувальний молотокРихтувальний молоток
ШилоШило
Брусок твердої деревиниБрусок твердої деревини
Електричний паяльникЕлектричний паяльник
ФлюсФлюс
4

Fit the top and handles

Hollow the top (Fig. 134), fit it to the body, wire its inner arc and solder it on. Cross handle: a strip about 1 3/4 in wide, wired with No. 12 B.W.G., bent to shape; cut two holes in the top with a small sharp chisel and solder the ends inside and on top. Back handle (Fig. 136): wire and bend it, solder a small boss under its upper part, and solder it opposite the spout with a thumb ring at the top. Solder three small hollowed studs under the bottom.

Матеріали для цього кроку:

Лист білої жерстіЛист білої жерсті1 top, handles, studs
Залізний дрітЗалізний дріт1 No. 12 B.W.G.
Олов'яно-свинцевий припійОлов'яно-свинцевий припій1 штука

Необхідні інструменти ({count})

Ножиці по металуНожиці по металу
Рихтувальний молотокРихтувальний молоток
Сталеве зубилоСталеве зубило
Електричний паяльникЕлектричний паяльник
ФлюсФлюс
5

Clean and paint

Clean with turpentine and whiting. Give two good coats of paint: red inside and green outside suit it.

Матеріали для цього кроку:

Олійна фарбаОлійна фарба2 coats

Необхідні інструменти ({count})

СкипидарСкипидар
Карбонат кальцію (крейда мелена)Карбонат кальцію (крейда мелена)

Матеріали

4

Необхідні інструменти

12

За цим кресленням виготовляють

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...