Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Three-Legged Router: A T-Frame on the Table Beside the Work, Its Depth Set by a Knob While Cutting (Willard & Young, 1939)
Forge

Створено

Forge

13. листопад 2026NO
6
0
0
0
0

Three-Legged Router: A T-Frame on the Table Beside the Work, Its Depth Set by a Knob While Cutting (Willard & Young, 1939)

Homer E. Willard and Frederick S. Young of Toledo, Ohio, received US 2,146,458, dated 7 February 1939, for a simple portable router with few moving parts. The motor sits in an open-fronted support in the middle of a T-shaped frame, so the bit and the work are always in view. The frame stands on three legs on the table beside the clamped work: two curved legs at one end, and at the other a screw with a knob. Turning the knob with one hand raises or lowers the bit while it cuts. We print the frame in PETG round a small DC motor. The sizes are ours.
Середній
About 1 day

Інструкції

1

Depth by the knob

Завантаження блокнота Jupyter…
2

Read US 2,146,458

"Thus, by turning the wrist in one direction or the other, the bit 19 may be raised or lowered, as required, without stopping the motor and without removing the hands from the tool."
3

Print the frame

The T-shaped frame 10: the motor support 13 with its ledge 14 (an 18 mm hole and two M4 holes 29 mm apart) and curved wall 15, open at the front 16; arm 11 to the cross with two curved legs 21, 22; arm 12 to a boss with an M10 nut trap for the screw leg 24. PETG, 0.2 mm layers, 40 % infill, 5 walls; print it legs up, ledge on the bed.
Файл дизайнуSTLCC0 - Free
4

Fit the motor

Print the frame. Fit the collet adapter on the motor's shaft, stand the motor in the support with its face on the ledge and the collet through the hole, and screw it down with two M4 screws. Wire it through a toggle switch to the DC supply as for our 1924 router.

Матеріали для цього кроку:

Філамент PETGФіламент PETG1 штука
ЕлектродвигунЕлектродвигун1 штука
Цанговий перехідник на вал двигунаЦанговий перехідник на вал двигуна1 штука
Гвинт із циліндричною головкою та внутрішнім шестигранникомГвинт із циліндричною головкою та внутрішнім шестигранником2 штук
ТумблерТумблер1 штука
Монтажний провідМонтажний провід1 штука
Термоусадочна трубкаТермоусадочна трубка1 штука

Необхідні інструменти ({count})

3D-принтер FDM3D-принтер FDM
Джерело живлення постійного струмуДжерело живлення постійного струму
Електричний паяльникЕлектричний паяльник
Набір шестигранних ключівНабір шестигранних ключів
5

The screw leg and knob

Press an M10 nut into the trap under the boss. Cut 100 mm of M10 threaded rod, round its lower end with a file so it slides on the table, and screw it up through the nut. Turn a hardwood knob 25, bore it, and glue it on the rod's top with a nut locked under it.

Матеріали для цього кроку:

Шестигранна гайкаШестигранна гайка2 штук
Шпилька різьбоваШпилька різьбова1 штука
Дошка з твердої деревиниДошка з твердої деревини1 штука
Столярний клейСтолярний клей1 штука

Необхідні інструменти ({count})

Ножівка по металуНожівка по металу
Набір напилківНабір напилків
Токарний верстат по деревуТокарний верстат по дереву
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Розвідний ключРозвідний ключ
6

Rout

Clamp the work down on the table between two strips. Fit a bit and stand the router on the table so its legs are beside the work and the bit is over it. Turn the knob until the bit just clears the work, switch on, and turn it down a little while moving the router over the area to be cut, one hand on arm 11 and the other on the knob.

Необхідні інструменти ({count})

Набір фрезНабір фрез
Дошка з твердої деревиниДошка з твердої деревини
Струбцина з напрямноюСтрубцина з напрямною
Цифровий штангенциркуль 6 дюймівЦифровий штангенциркуль 6 дюймів
Захисні окуляриЗахисні окуляри
7

Troubleshooting

Three-legged router troubleshooting.

Flow

Loading...
8

History and honest limits

**Homer E. Willard** and **Frederick S. Young** of Toledo, Ohio, US 2,146,458, dated 7 February 1939, filed 11 December 1935. They claimed "a portable router comprising a T-shaped frame having a semi-circular recess in the stem of the T, a bit-operating motor mounted in said recess and a leg projecting in the same direction as the bit from each of the ends of the frame", one leg "screw-threaded through the arm and terminating above the arm in an operating knob". Their work was an electrotype clamped on the table; their motor ran on mains. Ours is a small DC motor in a printed frame. They give no sizes; every size here is ours.

Матеріали

11

Необхідні інструменти

15

Файли дизайну

1

За цим кресленням виготовляють

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...