Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Rotary-Tub Spout Churn: A Friction Wheel Spins the Tub, a Fixed Spout Catches the Climbing Cream and Jets It Into a Basket
Buttercup

Створено

Buttercup

11. листопад 2026IE
7
0
0
0
0

Rotary-Tub Spout Churn: A Friction Wheel Spins the Tub, a Fixed Spout Catches the Climbing Cream and Jets It Into a Basket

Clark Wright and William Phelps of Sycamore, Illinois, received US 28,802, dated 19 June 1860, for a churn. The tub itself spins, carried on a plate that rests on a crank-turned friction wheel. The cream climbs the side until a flange stops it, where a fixed spout catches it and shoots it into a perforated basket hung loose in the middle; the butter collects in the basket while the milk runs out through its holes and climbs again. The patent gives no sizes; every size here is ours.
Просунутий
About 2 days, plus printing

Інструкції

1

How fast the tub must turn for the cream to climb

Завантаження блокнота Jupyter…
2

Cream flung outward and jetted, three months before

Sangster spins paddles to fling the cream. Wright and Phelps spin the whole tub.
3

Read US 28,802

"A quantity of cream being placed in the tub F, and the latter rapidly rotated by means of the crank D and friction wheel E, the cream ascends the sides of the tub by centrifugal force until arrested by the flange f and being caught by the spout K is deflected inward and projected in a forcible and continuous stream into the basket H, causing violent agitation in the body of cream as well as friction as it flows out through the apertures in the basket."
4

Print the basket H

Perforated cone basket 160 mm across at the top, 130 at the bottom, 150 tall, with a hub bored 12.6 mm. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Файл дизайнуSTLCC0 - Free
5

Print the spout K

Curved spout 40 mm wide, its mouth at the wall turning inward over 55 mm, with a hanger and a clamp that slides along the bar I. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Файл дизайнуSTLCC0 - Free
6

Base A, standard B, spindle G and plate g

Make a hardwood base 520 x 560 mm. Screw a hardwood standard 60 mm square in its middle, its top bored 16.6 mm to take a 16 mm stainless spindle. Cut a plywood disk plate 300 mm across, fix the spindle in its centre, and screw the bucket down on it, sealing the screw heads inside with silicone. Screw a ring of HDPE sheet, 26 mm wide, inside the bucket 340 mm up as the flange f, and a hardwood socket bored 12.6 mm in the floor's centre.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини2 штук
Лист фанериЛист фанери1 штука
Пруток із нержавкої сталіПруток із нержавкої сталі1 штука
Відро на 20 літрівВідро на 20 літрів1 штука
Лист ПЕВГЛист ПЕВГ1 штука
Брусок твердої деревиниБрусок твердої деревини1 штука
Столярний клейСтолярний клей1 штука
Шурупи по деревуШурупи по дереву16 штук
Силіконовий герметикСиліконовий герметик1 штука

Необхідні інструменти ({count})

Циркулярний верстатЦиркулярний верстат
ЕлектролобзикЕлектролобзик
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Набір перових сверделНабір перових свердел
Струбцина з напрямноюСтрубцина з напрямною
Набір викрутокНабір викруток
7

Friction wheel E, shaft C and crank D

Turn a hardwood wheel E 220 mm across with its rim rounded in section, as the patent's "regular convexity". Bolt two hardwood bearing blocks to the base so a 16 mm stainless shaft C runs straight out from under the spindle, at a height where the wheel, fixed on its inner end 50 mm from the spindle, just carries the plate. The shaft must point at the spindle, so the wheel rolls on the plate without scrubbing. Fix the wheel on the shaft, and a hardwood crank D with a dowel handle on its end; hold it with collars.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини1 штука
Пруток із нержавкої сталіПруток із нержавкої сталі1 штука
Шканти з твердої деревиниШканти з твердої деревини1 штука
Столярний клейСтолярний клей1 штука
Болт із півкруглою головкоюБолт із півкруглою головкою4 штук
Гайка-баранецьГайка-баранець4 штук
Shaft CollarShaft Collar2 штук

Необхідні інструменти ({count})

Токарний верстат по деревуТокарний верстат по дереву
Наждачний папірНаждачний папір
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Ножівка по металуНожівка по металу
Розвідний ключРозвідний ключ
8

Standards J, bar I, pin, basket H and spout K

Stand two hardwood standards J 30 x 30 mm either side of the bucket and join their tops with a bar I across it, bored 12.6 mm over the centre. Drop a 12 mm stainless pin through the bar into the floor socket and slide the basket onto it so it turns freely. Clip the spout's clamp on the bar so its mouth sits just under the flange, close to the wall, facing against the tub's turn; slide it in or out to suit.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини1 штука
Пруток із нержавкої сталіПруток із нержавкої сталі1 штука
Шурупи по деревуШурупи по дереву6 штук
Столярний клейСтолярний клей1 штука
Філамент PETGФіламент PETG1 штука

Необхідні інструменти ({count})

3D-принтер FDM3D-принтер FDM
Циркулярний верстатЦиркулярний верстат
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Ножівка по металуНожівка по металу
РулеткаРулетка
9

The build in 3D

FreeCAD model of this build, the tub cut open: the spindle and plate on the friction wheel and crank, the flange, the basket on its pin, the spout hanging from the bar, and the standards.
Файл дизайнуBLENDCC0 - Free
10

Churn

Pour about 5 litres of heavy cream at about 15 °C, checked with the thermometer, into the tub around the basket. Turn the crank briskly, timing it, until the cream climbs to the flange and runs from the spout into the basket. Keep on until the butter has gathered in the basket. Lift out the pin and basket with the butter, pour off the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Матеріали для цього кроку:

Жирні вершкиЖирні вершки5 l
Крупна морська сільКрупна морська сіль1 штука
ВодаВода1 штука

Необхідні інструменти ({count})

Термометр зі щупом, що лишається в стравіТермометр зі щупом, що лишається в страві
СекундомірСекундомір
Цифрові кухонні вагиЦифрові кухонні ваги
Велика миска з нержавкої сталіВелика миска з нержавкої сталі
11

Troubleshooting

Rotary-tub churn troubleshooting.

Flow

Loading...
12

History and honest limits

**Clark Wright** and **William Phelps** of Sycamore, DeKalb County, Illinois, US 28,802, 19 June 1860, "Churn". They claimed the rotary tub, stationary spout and basket together. Their wheel and plate meet as two crossed discs, the wheel's rounded rim avoiding both side thrust and broad rubbing faces. Every size here is ours.

Матеріали

17

Необхідні інструменти

17

Файли дизайну

3

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...