Collaboration
ART
BEAUTY & WELLNESS
CRAFT
CULTURE & HISTORY
ENTERTAINMENT
ENVIRONMENT
FOOD & DRINKS
REVERSE ENGINEERING
SCIENCES
SPORTS
TECHNOLOGY
WEARABLES
Top and Bottom Swages: Steel-Faced Iron Like a Fuller, Square Tang Below, Withy Handle Above, or Sprung Together (Edwinson, 1886)
Forge

Created by

Forge

14. November 2026NO
6
0
0
0
0

Top and Bottom Swages: Steel-Faced Iron Like a Fuller, Square Tang Below, Withy Handle Above, or Sprung Together (Edwinson, 1886)

Swages, the smith's top and bottom tools for bringing a weld back to round or square, from George Edwinson's smithing series in Amateur Work (1886): steel or steel-faced iron made like a fuller, the bottom tool tanged for the anvil's square hole, the top tool on a withy or iron-rod handle, or the pair coupled by a steel spring for single-handed work.
Advanced
A day at the forge per pair

Instructions

1

Read Edwinson

"They may be made of steel throughout, or of steel-faced iron. The method of making them is similar to that for making fullers and setts."
2

Weld the blanks

As for a fuller: upset an iron bar, split it into a fork with a hot set, weld in a forged steel wedge. Or use steel throughout.

Materials for this step:

Wrought Iron BarWrought Iron Bar1 piece
Crucible SteelCrucible Steel1 piece
Borax PowderBorax Powder1 piece

Tools needed:

Blacksmith ForgeBlacksmith Forge
AnvilAnvil
SledgehammerSledgehammer
Hot ChiselHot Chisel
Blacksmith TongsBlacksmith Tongs
3

Bottom swage

Forge the steel face into a block with a square tang that fits the square hole in the tail of the anvil, like a bottom set (his figs. 285-288).

Tools needed:

Blacksmith ForgeBlacksmith Forge
AnvilAnvil
HammerHammer
Blacksmith TongsBlacksmith Tongs
4

Top swage

Forge the matching top tool with a neck for its handle.

Tools needed:

Blacksmith ForgeBlacksmith Forge
AnvilAnvil
HammerHammer
Blacksmith TongsBlacksmith Tongs
5

Cut the grooves

Form the working groove in each face to the section you need: round, half-round, oval, diagonal, square or rectangular. Groove sizes are ours: match the bars you forge.

Tools needed:

Blacksmith ForgeBlacksmith Forge
FullerFuller
AnvilAnvil
Files (Hand File)Files (Hand File)
6

Handle or spring

Give the top tool a hazel-rod or iron-rod handle as for fullers and top sets. For single-handed work, couple the top and bottom tools with a steel spring (fig. 283).

Materials for this step:

Hazel Rods (Green, Flexible)Hazel Rods (Green, Flexible)1 piece
Mild Steel Round BarMild Steel Round Bar1 piece
Iron WireIron Wire1 piece
Spring Steel StripSpring Steel Strip1 piece

Tools needed:

Blacksmith ForgeBlacksmith Forge
AnvilAnvil
HammerHammer
7

Grind and harden

Grind the faces level so they fit each other, then heat the whole tool and harden it (his note for hand-worked dies).

Tools needed:

GrindstoneGrindstone
Blacksmith ForgeBlacksmith Forge
Quench BucketQuench Bucket
8

Use them

Work the weld at a red heat. Hold the bar and the top swage; the striker hits the top tool with a light sledge. Pass the bar to and fro, turning it for round. After each heat gauge the weld in the swage block or with callipers.

Tools needed:

Blacksmith ForgeBlacksmith Forge
SledgehammerSledgehammer
CaliperCaliper
9

Troubleshooting

Swage troubleshooting.

Flow

Loading...
10

History and honest limits

From George Edwinson, "Smithing and Forging" XI, **Amateur Work, Illustrated**, vol. VI (1886-87), pp. 259-260 and figs. 283-290 (checked on the archive.org scan amateurworkillus06lond). The forging steps follow his fuller method (pp. 14-16). Groove sizes, the spring stock and the tools are ours.

Materials

7

Tools Required

11

Related Blueprints

These blueprints share knowledge with this one — techniques, materials, or principles that connect them in the learning graph.

CC0 Public Domain

This blueprint is released under CC0. You are free to copy, modify, distribute, and use this work for any purpose, without asking permission.

Support the Maker by purchasing products through their Blueprint where they earn a Maker Commission set by Vendors, or create a new iteration of this Blueprint and include it as a connection in your own Blueprint to share revenue.

Discussion

(0)

Log in to join the discussion

Loading comments...