Collaboration
ART
BEAUTY & WELLNESS
CRAFT
CULTURE & HISTORY
ENTERTAINMENT
ENVIRONMENT
FOOD & DRINKS
REVERSE ENGINEERING
SCIENCES
SPORTS
TECHNOLOGY
WEARABLES
Navajo Blanket Weaving: Figure-8 Warp on Two Poles, String Healds, Batten Turned Flat to Open the Shed (Matthews, 1884)
Tex

Created by

Tex

15. November 2026FO
4
0
0
0
0

Navajo Blanket Weaving: Figure-8 Warp on Two Poles, String Healds, Batten Turned Flat to Open the Shed (Matthews, 1884)

How a Navajo (Diné) weaver made a blanket, as Washington Matthews recorded it: the warp wound in figures of eight between two poles so both sheds exist from the start, three-strand cords twined across each end, a string heald made loop by loop on a rod, and every pick beaten down with a broad oak batten that is first turned flat to open the shed.
Advanced
Weeks for a blanket

Instructions

1

His measures

Loading Jupyter Notebook...
2

Read Matthews

"It is by the vigorous use of the batten that the Navajo serapes are rendered water-proof."
3

Lay the warp

On the ground make a frame of four sticks: rough saplings at the sides, smooth round poles top and bottom, as far apart as the blanket is long. Tie the warp string to pole 1, take it over pole 2, back under 2 and over 1, and on: the turns cross in the middle in figures of eight, which makes both sheds. Tie off on pole 2 and put a rod in each shed, the rods tied together at their ends.

Materials for this step:

Undyed Wool YarnUndyed Wool Yarn1 piece
Green Wood PolesGreen Wood Poles1 piece

Tools needed:

KnifeKnife
4

Twine the end cords

Tie three strings together. Sitting outside one pole, fix them left of the warp; take one strand under the first turn of warp, twist a second strand with the others and take in the second bend, the third the third bend, and so along. Pull the cord tight to space the threads, and do the same at the other pole. These become the stout end edges.

Materials for this step:

CordageCordage1 piece

Tools needed:

KnifeKnife
5

Mount and make the healds

Bind the end cords to the loom beams (see the loom blueprint). Keep the upper-shed rod. For the lower shed: pass the end of a ball of string left through the shed, tie a loop on a slender rod, then with a finger draw a fold of string between each pair of front threads, give it one twist into a loop and push the rod through, left to right, until every front thread is in a loop; tie the string to the rod.

Materials for this step:

CordageCordage1 piece

Tools needed:

Simple Frame LoomSimple Frame Loom
KnifeKnife
6

Weave

Sit on the ground facing the loom and weave upward. Lower shed: pull the healds toward you (about 1 in. opening), slide the batten in edgewise and turn it flat to open the shed about 3 in. (8 cm), pass the weft, push it down with the reed-fork, turn the batten edgewise and beat hard. Upper shed: let the healds go, push the shed-rod down to them, and weft, fork and batten again. Pass weft only as far as the batten reaches, rarely over 3 ft (90 cm). Two stout yarn cords, tied at the cloth-beam just outside the warp and up to the yarn-beam, make the side edges.

Materials for this step:

Dyed Wool YarnDyed Wool Yarn1 piece

Tools needed:

Simple Frame LoomSimple Frame Loom
7

Lower the web

When the work gets too high, loosen the spiral rope, lower the yarn-beam, fold the woven part and sew the fold's upper edge tightly to the cloth-beam (needle ours). Most weavers weave a little at the top before finishing the middle, so both ends match.

Materials for this step:

CordageCordage1 piece

Tools needed:

Sewing NeedleSewing Needle
Simple Frame LoomSimple Frame Loom
8

Troubleshooting

Weaving troubleshooting.

Flow

Loading...
9

History and honest limits

From Washington Matthews, "Navajo Weavers", **3rd Annual Report of the Bureau of Ethnology** (1884), pp. 378-381, Fig. 43 and Plate XXXV (checked on the archive.org scan 101714660.nlm.nih.gov; p. 380 taken from the scan's text layer). In coarser blankets the end cords were taken out and the warp tied in pairs as a fringe. Yarn amounts, frame size and the needle are ours.

Materials

4

Tools Required

3

CC0 Public Domain

This blueprint is released under CC0. You are free to copy, modify, distribute, and use this work for any purpose, without asking permission.

Support the Maker by purchasing products through their Blueprint where they earn a Maker Commission set by Vendors, or create a new iteration of this Blueprint and include it as a connection in your own Blueprint to share revenue.

Discussion

(0)

Log in to join the discussion

Loading comments...