Collaboration
ART
BEAUTY & WELLNESS
CRAFT
CULTURE & HISTORY
ENTERTAINMENT
ENVIRONMENT
FOOD & DRINKS
REVERSE ENGINEERING
SCIENCES
SPORTS
TECHNOLOGY
WEARABLES
Valentine and Sweets Box: a Card Tray Stacked on a Candy Tray, With Wings That Hold the Card (Richter, 1908)
Tex

Created by

Tex

13. November 2026FO
6
0
0
0
0

Valentine and Sweets Box: a Card Tray Stacked on a Candy Tray, With Wings That Hold the Card (Richter, 1908)

Harry Richter of Omaha received US 901,476, dated 20 October 1908, for a box with two trays under one lid: sweets below, and above them a deeper tray for a valentine, held flat by little card wings so it never touches the lid. The trays stack on an inner rim and cannot slide, and come apart easily. We make it from pasteboard and card. All sizes are ours.
Beginner
About 3 hours

Instructions

1

Box sizes

Loading Jupyter Notebook...
2

Read US 901,476

"The device affords a secure housing for these articles, and by reason of the formation and arrangement of parts, it may be economically constructed."
3

Make the lower tray

Cut the bottom 1 from pasteboard and glue an upturned rim 3 round it from a card strip, scored and folded at the corners. Glue a second strip inside it, his sustaining leaf 4, standing about 6 mm (ours) above the rim all round.

Materials for this step:

PasteboardPasteboard1 piece
Card StockCard Stock1 piece
GlueGlue1 piece

Tools needed:

PencilPencil
RulerRuler
Craft KnifeCraft Knife
Bone FolderBone Folder
Glue BrushGlue Brush
4

Make the upper tray

Cut the bottom 6 the same size and glue a deeper rim 8 round it. Glue an enclosing strip 9 round the outside of rim 8, a little lower than it at the top and reaching about 6 mm below the bottom (his portion 10), so the upper tray sits on the lower one with the enclosing strip round the lower tray's inner rim.

Materials for this step:

PasteboardPasteboard1 piece
Card StockCard Stock1 piece
GlueGlue1 piece

Tools needed:

RulerRuler
Craft KnifeCraft Knife
Bone FolderBone Folder
Glue BrushGlue Brush
5

Make the card wings

Cut two small triangular card wings, each with a folded flange 16. Glue the flanges inside rim 8, midway between the ends, one each side, so the wings can be bent down over the bottom: their lower edges 17 press on the valentine and keep it off the lid.

Materials for this step:

Card StockCard Stock1 piece
GlueGlue1 piece

Tools needed:

Craft KnifeCraft Knife
Bone FolderBone Folder
Glue BrushGlue Brush
6

Make the lid

Cut the top leaf 11 to fit over the upper tray and glue a rim 13 round it, sized so it rests on the enclosing strip 9, as his Fig. 4.

Materials for this step:

PasteboardPasteboard1 piece
Card StockCard Stock1 piece
GlueGlue1 piece

Tools needed:

RulerRuler
Craft KnifeCraft Knife
Bone FolderBone Folder
Glue BrushGlue Brush
7

Fill and close it

Put the sweets in the lower tray, set the upper tray on it, lay the valentine in and bend the wings down over it, and put the lid on. Lift the upper tray off to reach the sweets.
8

Troubleshooting

Valentine box troubleshooting.

Flow

Loading...
9

History and honest limits

**Harry Richter** of Omaha, US 901,476, dated 20 October 1908, filed 29 November 1907. He claimed a box with a lower receptacle with an inner sustaining rim, an upper receptacle with an outer enclosing rim, "flexible holding-wings having flanges secured upon the inner sides of the integral upturned rim", and a cover. He made the wings "preferably of card board" and gives no sizes: the pasteboard, all sizes and glue are ours.

Materials

3

Tools Required

5

This blueprint makes

Related Blueprints

These blueprints share knowledge with this one โ€” techniques, materials, or principles that connect them in the learning graph.

CC0 Public Domain

This blueprint is released under CC0. You are free to copy, modify, distribute, and use this work for any purpose, without asking permission.

Support the Maker by purchasing products through their Blueprint where they earn a Maker Commission set by Vendors, or create a new iteration of this Blueprint and include it as a connection in your own Blueprint to share revenue.

Discussion

(0)

Log in to join the discussion

Loading comments...