ART
BEAUTY & WELLNESS
CRAFT
CULTURE & HISTORY
ENTERTAINMENT
ENVIRONMENT
FOOD & DRINKS
REVERSE ENGINEERING
SCIENCES
SPORTS
TECHNOLOGY
WEARABLES
The Collapsible Tube: A Container That Is Always Full
Charlie

Created by

Charlie

27. September 2026DE
6
0
0
0
0

The Collapsible Tube: A Container That Is Always Full

Before the 1840s a painter kept ground oil colour in pig's bladders tied with string, pricked to squeeze some out; once opened, the paint began to dry. A tube of soft metal, squeezed from the end and capped, keeps the rest sealed from the air. US 2,252, dated 11 September 1841, was granted to John Rand, then living at Howland Street, Middlesex, England — the American portrait painter John Goffe Rand. Its drawing sheet is titled "Metal Rolls for Paint". Tubes of grain-tin, lead or pewter thin enough "to be caused to be permanently collapsed" are filled, closed at both ends, pierced or fitted with a screw-capped nozzle, and rolled up from the end as the paint is used. This rung works out why a soft metal tube stays collapsed, and fills and tests tubes of paint.
Beginner
About 2 hours

Instructions

1

Dose per millimetre and fold strain

Loading Jupyter Notebook...
2

Why paint must be kept from the air

Oil paint cures by reacting with oxygen. The embedded blueprint explains the drying mechanisms that a sealed tube stops.
3

Read US 2,252

Rand's invention relates to "a mode of preserving paints and other fluids by confining them in close metallic vessels so constructed as to collapse with slight pressure, and thus force out the paint or fluid confined therein through proper openings", which can then be closed air-tight. The vessels are "at all times full, whatever be the quantity of fluid matter remaining therein". He names "grain-tin, lead, and pewter" as the best and cheapest metals, of such thickness "as readily to yield to pressure and to be caused to be permanently collapsed". Fig. 1's vessel is "made of grain-tin drawn into a tube", the metal "about one seventy-fifth of an inch in thickness", its ends closed by melting the pressed edges or by soldering; a pair of forceps b holds the end for closing it with a blowpipe or hot iron. A hole is made at c and "it is better that the pressure should be made at the end, d, of the vessel", so the collapsed end "may be rolled up". Fig. 4 adds a short tube with "a screw-cap". He warns that the fluid must not be one "chemically prejudicially acted on by the metal employed".
4

Fill tubes and test the seal

Mix a little oil paint from the set with a few drops of linseed oil. Fill two empty paint tubes from the open end with a palette knife, fold the end over twice with flat-nose pliers and crimp it flat. Put the same paint in a small open-topped jar with a loose lid. Each day for a week, squeeze a pea of paint from a tube and rolling up the end, and take a pea from the jar. Note when the jar's paint grows a skin and when the tube's does. Measure the flattened length per squeeze with the caliper and compare with the notebook's millimetres per millilitre.

Materials for this step:

Empty Paint TubesEmpty Paint Tubes2 pieces
Oil Paint SetOil Paint Set1 piece
Linseed OilLinseed Oil1 piece
Glass JarGlass Jar1 piece

Tools needed:

Flat-Nose PliersFlat-Nose Pliers
Digital Caliper 6-InchDigital Caliper 6-Inch
Craft KnifeCraft Knife
5

A tube that dries out or leaks

Collapsible tube troubleshooting.

Flow

Loading...
6

History and honest limits

**US 2,252**, dated 11 September 1841, was granted to **John Rand**, a citizen of the United States then living in Middlesex, England; he is the portrait painter John Goffe Rand. It claims the mode of preserving paint in vessels that collapse by slight pressure as their contents are removed. **Honest limits.** Tin's modulus and yield stress in the notebook are typical values; lead and pewter behave similarly. Lead tubes are not used for food or cosmetics today.

Materials

4

Tools Required

3

CC0 Public Domain

This blueprint is released under CC0. You are free to copy, modify, distribute, and use this work for any purpose, without asking permission.

Support the Maker by purchasing products through their Blueprint where they earn a Maker Commission set by Vendors, or create a new iteration of this Blueprint and include it as a connection in your own Blueprint to share revenue.

Discussion

(0)

Log in to join the discussion

Loading comments...