NGHỆ THUẬT
LÀM ĐẸP VÀ SỨC KHỎE
THỦ CÔNG
VĂN HÓA VÀ LỊCH SỬ
GIẢI TRÍ
MÔI TRƯỜNG
THỰC PHẨM VÀ ĐỒ UỐNG
KỸ THUẬT NGƯỢC
KHOA HỌC
THỂ THAO
CÔNG NGHỆ
THIẾT BỊ ĐEO

Counter-Rotating Egg Beater: One Wheel, Two Beaters Turning Opposite Ways
A single whisk carries the egg round with it rather than cutting through it.
James F. Monroe of Fitchburg, Massachusetts, and E. P. Monroe of New York received US 23,694, dated 19 April 1859, for an egg beater: a frame clamped to a table carries a bevel wheel turned by a handle, gearing into two pinions on opposite sides of it; one turns an inner beater of bent wires, the other an outer beater round it, "in opposite directions."
This rung works out the beater speeds, then prints the crown wheel and pinions, bends the beaters, and times a beating.
Trung cấp
About 5 hours, plus printing
Hướng dẫn
1
1
Beater speeds
Beater speeds
Đang tải sổ tay Jupyter…
2
2
The gear train it uses
The gear train it uses
The embedded blueprint works gear ratios and direction. Monroe takes two pinions off opposite sides of one wheel so they turn opposite ways.
3
3
Read US 23,694
Read US 23,694
"This invention consists in arranging in an adjustable frame two beaters, one inside the other, which receive motion in opposite directions by means of two pinions which gear into a large bevel wheel and on opposite sides of the same, so that by rotating the bevel wheel by means of a handle the beaters receive the required motion."
4
4
Print the gears
Print the gears
Print the 48-tooth crown wheel (/uploads/blueprints/counter-rotating-egg-beater-crown-wheel.stl) and two 12-tooth pinions (/uploads/blueprints/counter-rotating-egg-beater-pinion.stl). Print in PETG at 0.2 mm layers, 30 % infill, 4 walls.
Vật liệu cho bước này:
Sợi in PETG1 cáiCông cụ cần thiết:
Máy in 3D sợi nhựa (FDM)5
5
Build the frame
Build the frame
Cut a plywood upright and two arms. Bolt the crown wheel to the upright on an M5 screw with washers so it turns freely, and fix a handle screw near its rim. Drill the arms 5 mm on the line through both pinions' centres.
Vật liệu cho bước này:
Tấm gỗ dán1 cái
Vít máy1 cái
Vòng đệm phẳng1 cái
Đai ốc lục giác1 cái
Vít gỗ #8 x 1"1 cáiCông cụ cần thiết:
Cưa lọng tay
Máy khoan pin
Bộ mũi khoan
Mỏ lết
Bộ tua vít6
6
Arbor and inner beater
Arbor and inner beater
Cut 200 mm of 5 mm rod. Epoxy one pinion on it to mesh at the wheel's top, and bend two wire loops 28 mm across at its lower end.
Vật liệu cho bước này:
Thanh thép mềm1 cái
Dây thép không gỉ1 cái
Keo epoxy hai thành phần1 cáiCông cụ cần thiết:
Cưa sắt
Kìm mỏ tròn
Kìm mỏ dẹt7
7
Sleeve and outer beater
Sleeve and outer beater
Glue the second pinion to a length of silicone tube sleeved loosely over the rod, meshing at the wheel's bottom. Bend two wire loops 48 mm across and fix them to the sleeve's lower end, round the inner beater.
Vật liệu cho bước này:
Dây thép không gỉ1 cái
Keo epoxy hai thành phần1 cáiCông cụ cần thiết:
Kìm mỏ tròn
Kìm mỏ dẹt
Thước cặp điện tử 6 inch8
8
The patent drawing
The patent drawing
US 23,694 drawing sheet, public domain (expired patent).

9
9
Beat egg whites
Beat egg whites
Clamp the frame to the table over the bowl with two egg whites. Turn the handle about once a second and time how long until they hold stiff peaks.

Vật liệu cho bước này:
Trứng2 cáiCông cụ cần thiết:
Tô trộn thép không gỉ (lớn)
Đồng hồ bấm giờ10
10
Beaters that turn together, jam or clash
Beaters that turn together, jam or clash
Counter-rotating egg beater troubleshooting.
Flow
Loading...
11
11
History and honest limits
History and honest limits
**James F. Monroe** of Fitchburg, Massachusetts, and **E. P. Monroe** of New York, assignors to E. P. Monroe, received US 23,694, dated 19 April 1859, reissued 16 October 1860 (No. 1,062). The frame's fork clamps to a table with a set screw and washer. The second pinion lies loose on the arbor, driving the outer beater whose lower collar turns loosely round the arbor's end. They noted it also mixes paint.
**Honest limits.** FDM prints hold food in their layer lines, so wash well and replace when worn. A crown wheel and spur pinions stand in for his bevel gears, and a silicone sleeve for his loose pinion. Your times are the result.
Vật liệu
11- 1 cáiTạm thời
- 1 cáiTạm thời
- 1 cáiTạm thời
- 1 cáiTạm thời
- 1 cáiTạm thời
- 1 cáiTạm thời
- 1 cáiTạm thời
- 2 cáiTạm thời
- Tạm thời
- 1 cáiTạm thời
- 2 cáiTạm thời
Công cụ yêu cầu
12- Tạm thời
- Tạm thời
- 1 vendor sell this, none ship to you yetTạm thời
- Tạm thời
- Tạm thời
- Tạm thời
- Tạm thời
- Tạm thời
- Tạm thời
- Tạm thời
- Tạm thời
- Tạm thời
Bản thiết kế này làm ra
Blueprint liên quan
Các blueprint này chia sẻ kiến thức — kỹ thuật, vật liệu hoặc nguyên tắc
CC0 Phạm vi công cộng
Bản thiết kế này được phát hành theo CC0. Bạn tự do sao chép, sửa đổi, phân phối và sử dụng cho bất kỳ mục đích nào mà không cần xin phép.
Hỗ trợ nhà sáng tạo bằng cách mua sản phẩm qua bản thiết kế, nơi họ nhận Hoa hồng nhà sáng tạo do nhà bán hàng đặt, hoặc tạo phiên bản mới và kết nối trong bản thiết kế riêng để chia sẻ doanh thu.



