NGHỆ THUẬT
LÀM ĐẸP VÀ SỨC KHỎE
THỦ CÔNG
VĂN HÓA VÀ LỊCH SỬ
GIẢI TRÍ
MÔI TRƯỜNG
THỰC PHẨM VÀ ĐỒ UỐNG
TƯƠNG LAI XANH
KỸ THUẬT NGƯỢC
School Projects
KHOA HỌC
THỂ THAO
CÔNG NGHỆ
THIẾT BỊ ĐEO
Building a Khaen — The Lao Free-Reed Mouth Organ
Woody

Tạo bởi

Woody

3. tháng Bảy 2026NO
4
0
0
0
0

Building a Khaen — The Lao Free-Reed Mouth Organ

Build a khaen, the national instrument of Laos: a flat raft of long paired bamboo pipes passing through a small hardwood windchest, each voiced by a springy metal free reed. Cover a pipe's hole and it sounds; hold some for a drone while others play a tune — and it sings on both blow and draw. A serious maker build in the free reed, in raft form.
Trung cấp
Several hours over a few sessions

Hướng dẫn

1

A raft of singing bamboo

The khaen is the free-reed mouth organ of Laos and northeast Thailand: long bamboo pipes laid flat in a raft through a small windchest. Blow or draw, cover the holes, and it pours out drones and melody at once for mor lam music.
2

Cut the pipes

Cut a set of long, thin bamboo pipes in graduated lengths and lay them in two neat rows — a raft. Fourteen to sixteen pipes make a full khaen; start with fewer.

Vật liệu cho bước này:

BambooBamboo1 cái

Công cụ cần thiết:

HacksawHacksaw
3

Carve the windchest

Carve a small hardwood block into a hollow windchest with a mouth-hole at one end. The whole raft of pipes will pass through this chest.

Vật liệu cho bước này:

Bloodwood BoardBloodwood Board1 cái

Công cụ cần thiết:

Sloyd Carving KnifeSloyd Carving Knife
4

Make the free reeds

From thin metal, cut a tiny free tongue for each pipe — a springy strip that swings cleanly through a matching slot, fixed at one end and free at the other.

Vật liệu cho bước này:

Brass Shim (Reed Stock)Brass Shim (Reed Stock)1 cái

Công cụ cần thiết:

Metal FileMetal File
5

Mount a reed in each pipe

Set a reed into each pipe at the point where the pipe will cross inside the windchest, sealed airtight, with the tongue free to swing.

Vật liệu cho bước này:

BeeswaxBeeswax1 cái
6

Seal the pipes into the windchest

Pass all the pipes through the windchest so their reeds sit inside it, and seal every gap with black wax so no air can escape except through the reeds.

Vật liệu cho bước này:

BeeswaxBeeswax1 cái
7

Cut a finger hole in each pipe

Cut one finger hole in each pipe, just outside the windchest. This hole is the on/off switch for that pipe's note.

Công cụ cần thiết:

AwlAwl
8

Test a pipe

Cup the windchest to your mouth, blow gently, and cover one pipe's hole. Covering the hole drives the air through that pipe's reed, and it sounds.
9

Drone and switch

An open hole lets air escape and stays silent; a covered hole sings. Hold a couple of holes covered for a constant drone while your other fingers pick out notes.
10

Tune the reeds

Add a dab of wax to a reed's tip to LOWER its note, or file the tip thinner to RAISE it, tuning the pipes to the khaen's seven-note scale.

Vật liệu cho bước này:

BeeswaxBeeswax1 cái

Công cụ cần thiết:

Metal FileMetal File
11

Play drone and melody

Hold a drone under a running melody and breathe IN as well as out — free reeds sound both ways, so the khaen never has to stop for breath. That endless ripple is the sound of mor lam.
12

Compendium — the free reed, in a raft

The khaen works on the free reed, exactly like the Chinese sheng: a thin metal tongue that swings freely back and forth THROUGH a close-fitting slot as air flows past, chopping the airflow into a steady tone at the tongue's own pitch and speaking equally whether you blow or draw. But where the sheng gathers short pipes upright in a gourd bowl, the khaen lays long paired bamboo pipes flat in a raft that runs through a small hardwood windchest cupped in both hands — a different shape for the same idea, spread across Asia. Each pipe holds one reed, and its finger hole is a switch: only a covered hole forces air through the reed, so a player can hold some holes down for a continuous drone while other fingers pick out a melody above it, with no pause to breathe — the endlessly rippling texture of Lao and Isan mor lam song. The reeds are tuned by filing them thinner to raise the pitch or loading their tips with a dab of wax to lower it, set to the khaen's seven-note scale, and the whole windchest is sealed with black insect wax so that every breath goes only through the reeds. The free reed that both the khaen and the sheng are built on is the ancestor of the Western harmonica, accordion and reed organ, and its distant cousin is the plucked tongue of the jaw harp. The national instrument of Laos, the khaen is recognised by UNESCO as part of humanity's living heritage.

Vật liệu

4

Công cụ yêu cầu

4

You can swap these in

Can't get one of the materials? Swap it for an equivalent — these work just as well.

Blueprint liên quan

Các blueprint này chia sẻ kiến thức — kỹ thuật, vật liệu hoặc nguyên tắc

CC0 Phạm vi công cộng

Bản thiết kế này được phát hành theo CC0. Bạn tự do sao chép, sửa đổi, phân phối và sử dụng cho bất kỳ mục đích nào mà không cần xin phép.

Hỗ trợ nhà sáng tạo bằng cách mua sản phẩm qua bản thiết kế, nơi họ nhận Hoa hồng nhà sáng tạo do nhà bán hàng đặt, hoặc tạo phiên bản mới và kết nối trong bản thiết kế riêng để chia sẻ doanh thu.

Thảo luận

(0)

Đăng nhập để tham gia thảo luận

Đang tải bình luận...