Hợp tác
NGHỆ THUẬT
LÀM ĐẸP VÀ SỨC KHỎE
THỦ CÔNG
VĂN HÓA VÀ LỊCH SỬ
GIẢI TRÍ
MÔI TRƯỜNG
THỰC PHẨM VÀ ĐỒ UỐNG
KỸ THUẬT NGƯỢC
KHOA HỌC
THỂ THAO
CÔNG NGHỆ
THIẾT BỊ ĐEO
Hind Horseshoe: Round-Pointed Toe, No Seating, Nail Holes in the Front Two-Thirds (Lungwitz and Adams, Text-Book of Horseshoeing, 1913)
Forge

Tạo bởi

Forge

13. tháng Mười Một 2026NO
6
0
0
0
0

Hind Horseshoe: Round-Pointed Toe, No Seating, Nail Holes in the Front Two-Thirds (Lungwitz and Adams, Text-Book of Horseshoeing, 1913)

A flat hind horseshoe from Lungwitz and Adams, A Text-Book of Horseshoeing (1913). It is made "in like manner" as the front shoe, but the branches are bent to a different curve, giving a round-pointed toe, the hoof side is not concaved, and the nail holes run further back. Fitting and nailing the shoe to the horse, calks and clips are not covered here.
Trung cấp
8-15 minutes a pair, once practised

Hướng dẫn

1

Bar length and sizes

Đang tải sổ tay Jupyter…
2

Read Lungwitz and Adams

"The hind shoe is made in like manner, but the branches are not bent in a circle but given that form shown in Fig. 106."
3

Measure and cut the bar

Measure the hoof from the point of the toe to the buttress and its greatest width; add them for the bar length. Trace the outline on stiff paper if you want to keep it. Cut the bar.

Vật liệu cho bước này:

Thanh sắt rènThanh sắt rèn1 cái

Công cụ cần thiết:

Thước dây cuộnThước dây cuộn
Bút chìBút chì
Tờ giấy dàyTờ giấy dày
Lò rèn của thợ rènLò rèn của thợ rèn
Đục cắt trên đeĐục cắt trên đe
Kìm rènKìm rèn
4

Bend the outer branch to the hind curve

Heat the bar white-hot just beyond its middle and bend it over the sledge head on the anvil face with the turning hammer, as for the front shoe, but bend the branch to the flatter, angled curve of his Fig. 106, not to a circle. The outer branch is made first, the right shoe first in a pair. Draw out the end with the sledge.

Công cụ cần thiết:

Lò rèn của thợ rènLò rèn của thợ rèn
Đe mỏ nhọnĐe mỏ nhọn
Xe quệtXe quệt
Búa làm trònBúa làm tròn
Kìm rènKìm rèn
5

Bevel, flatten and shape

Bevel the branch on the horn, then flatten it. Bending the toe of a hind shoe backs up the inner edge and thins the outer, so hammer the shoe smooth and even. Shape it so the toe is round-pointed, "yet not too much so", as in his Fig. 116.

Công cụ cần thiết:

Đe mỏ nhọnĐe mỏ nhọn
Búa làm trònBúa làm tròn
Kìm rènKìm rèn
6

Round the inner edge and fuller

Concaving is not necessary: just round the inner edge of the web. Fuller the ground side as for the front shoe, to about two-thirds of the thickness.

Công cụ cần thiết:

Đe mỏ nhọnĐe mỏ nhọn
Fuller (sắt tạo rãnh)Fuller (sắt tạo rãnh)
Xe quệtXe quệt
Búa làm trònBúa làm tròn
Kìm rènKìm rèn
7

Stamp the nail holes

Stamp and pritchel the nail holes in the front two-thirds of the shoe, none at the toe: usually one more than a front shoe, seldom more than eight. Set each as far from the outer edge as the wall is thick; on a hind hoof the wall is nearly as thick at the quarters as at the toe.

Công cụ cần thiết:

Đe mỏ nhọnĐe mỏ nhọn
Đột nóngĐột nóng
Đục lỗ đinh móng ngựaĐục lỗ đinh móng ngựa
Búa làm trònBúa làm tròn
Kìm rènKìm rèn
8

Make the second branch and finish

Make the inner branch the same way, turned to the left. Go over the outer edge on the horn and hammer the bearing surface smooth and level. Rough it out in two heats if you can.

Công cụ cần thiết:

Lò rèn của thợ rènLò rèn của thợ rèn
Đe mỏ nhọnĐe mỏ nhọn
Búa làm trònBúa làm tròn
Fuller (sắt tạo rãnh)Fuller (sắt tạo rãnh)
Đột nóngĐột nóng
Đục lỗ đinh móng ngựaĐục lỗ đinh móng ngựa
Kìm rènKìm rèn
9

Troubleshooting

Hind shoe troubleshooting.

Flow

Loading...
10

History and honest limits

From **A Text-Book of Horseshoeing**, by A. Lungwitz and John W. Adams, 11th edition, J. B. Lippincott, 1913 (Project Gutenberg 66786), chapter III F. His Fig. 116 shows a hind shoe with toe- and heel-calks; the calks and the toe-clip are not made here, as this chapter gives no method for forging heel-calks or drawing clips. Fitting and nailing are not covered. The metric figures are ours.

Vật liệu

1

Công cụ yêu cầu

12

Bản thiết kế này làm ra

CC0 Phạm vi công cộng

Bản thiết kế này được phát hành theo CC0. Bạn tự do sao chép, sửa đổi, phân phối và sử dụng cho bất kỳ mục đích nào mà không cần xin phép.

Hỗ trợ nhà sáng tạo bằng cách mua sản phẩm qua bản thiết kế, nơi họ nhận Hoa hồng nhà sáng tạo do nhà bán hàng đặt, hoặc tạo phiên bản mới và kết nối trong bản thiết kế riêng để chia sẻ doanh thu.

Thảo luận

(0)

Đăng nhập để tham gia thảo luận

Đang tải bình luận...