NGHỆ THUẬT
LÀM ĐẸP VÀ SỨC KHỎE
THỦ CÔNG
VĂN HÓA VÀ LỊCH SỬ
GIẢI TRÍ
MÔI TRƯỜNG
THỰC PHẨM VÀ ĐỒ UỐNG
TƯƠNG LAI XANH
KỸ THUẬT NGƯỢC
School Projects
KHOA HỌC
THỂ THAO
CÔNG NGHỆ
THIẾT BỊ ĐEO
Carving a Wooden Clog — The All-Wood Sabot from a Single Green Block
Woody

Tạo bởi

Woody

2. tháng Bảy 2026NO
2
0
0
0
0

Carving a Wooden Clog — The All-Wood Sabot from a Single Green Block

Across rural Europe the wooden clog — the French sabot, the Dutch klomp — kept feet warm and dry for centuries. Each shoe is carved from a single block of green hardwood: the outside shaped like a foot, the inside hollowed out to receive it. Green (unseasoned) alder, willow or beech is used because it carves easily and splits little, then hardens as it dries. This blueprint carves one clog from froe-split billet to finished shoe, then repeats for the matching pair, using only edge tools.
Trung cấp
6

Hướng dẫn

1

Split a clean billet

Split a straight-grained block of green alder, willow or beech to a little larger than the foot, using the froe driven with a wooden mallet. Choose a length free of knots so the wood carves cleanly.

Vật liệu cho bước này:

Hardwood BlockHardwood Block1 cái

Công cụ cần thiết:

FroeFroe
Wooden MalletWooden Mallet
2

Rough out the foot profile

With the hatchet, chop the billet down to the rough shape of a foot seen from the side — a flat sole, an upturned toe, and a squared heel. Leave the block oversize everywhere for now.

Công cụ cần thiết:

HatchetHatchet
3

Mark the sole and top outlines

Stand the block on the wearer's foot or a pattern and mark the outline of the sole and the top opening with the point of the carving knife, so you have clear lines to carve to.

Công cụ cần thiết:

Sloyd Carving KnifeSloyd Carving Knife
4

Shape the outside with the drawknife

Clamp the block and draw the drawknife toward you to shape the rounded outside of the clog — the swell of the toe, the waist at the instep, and the flat of the sole. Work down to the marked lines.

Công cụ cần thiết:

Draw KnifeDraw Knife
5

Refine the curves with a spokeshave

Smooth the toe curve, the sides and the instep with the spokeshave, fairing the outside into an even foot shape ready to hollow.

Công cụ cần thiết:

SpokeshaveSpokeshave
6

Bore out the mouth

Bore down into the top opening with the hand auger to remove the bulk of the inside waste quickly, stopping short of the sole so you do not bore through.

Công cụ cần thiết:

Hand AugerHand Auger
7

Hollow the foot cavity

Hollow the inside to the shape of a foot with the hook knife and gouge, driven by the mallet where needed. Follow the curve of the sole and open out under the instep, leaving even walls.

Công cụ cần thiết:

Hook Knife (Spoon Carving)Hook Knife (Spoon Carving)
GougeGouge
Wooden MalletWooden Mallet
8

Fit the cavity to the foot

Test the hollow against the foot it must fit: the sole should sit flat, the toes have room, and the walls be thin enough to be light but thick enough to be strong. Pare away any tight spots.

Công cụ cần thiết:

Hook Knife (Spoon Carving)Hook Knife (Spoon Carving)
9

Cut the instep throat

Shape the opening at the top of the foot — the 'throat' — with the gouge and carving knife so the foot slides in and the clog grips the instep without pinching.

Công cụ cần thiết:

GougeGouge
Sloyd Carving KnifeSloyd Carving Knife
10

Smooth inside and out

Pare every surface smooth, inside and out, with the carving knife and spokeshave, removing tool ridges so nothing chafes the foot and the outside is clean.

Công cụ cần thiết:

Sloyd Carving KnifeSloyd Carving Knife
SpokeshaveSpokeshave
11

Carve the matching clog

Repeat every step to carve the second clog as a mirror image of the first, so the pair matches in length, depth and shape — one left, one right.

Vật liệu cho bước này:

Hardwood BlockHardwood Block1 cái

Công cụ cần thiết:

HatchetHatchet
Draw KnifeDraw Knife
Hook Knife (Spoon Carving)Hook Knife (Spoon Carving)
12

Dry the pair slowly

Set the finished green-wood clogs to dry slowly in a cool, airy place away from direct heat. As the wood seasons it hardens and the clogs become light and durable — drying too fast would crack them.

Vật liệu

1

Công cụ yêu cầu

9

Vật liệu bản thiết kế liên kết

You can swap these in

Can't get one of the materials? Swap it for an equivalent — these work just as well.

CC0 Phạm vi công cộng

Bản thiết kế này được phát hành theo CC0. Bạn tự do sao chép, sửa đổi, phân phối và sử dụng cho bất kỳ mục đích nào mà không cần xin phép.

Hỗ trợ nhà sáng tạo bằng cách mua sản phẩm qua bản thiết kế, nơi họ nhận Hoa hồng nhà sáng tạo do nhà bán hàng đặt, hoặc tạo phiên bản mới và kết nối trong bản thiết kế riêng để chia sẻ doanh thu.

Thảo luận

(0)

Đăng nhập để tham gia thảo luận

Đang tải bình luận...