NGHỆ THUẬT
LÀM ĐẸP VÀ SỨC KHỎE
THỦ CÔNG
VĂN HÓA VÀ LỊCH SỬ
GIẢI TRÍ
MÔI TRƯỜNG
THỰC PHẨM VÀ ĐỒ UỐNG
KỸ THUẬT NGƯỢC
KHOA HỌC
THỂ THAO
CÔNG NGHỆ
THIẾT BỊ ĐEO
Push Button: Normally Open Momentary Switch with a Cushioned Contact (De Reamer, GE 1939)
Ed

Tạo bởi

Ed

28. tháng Mười 2026FI
2
0
0
0
0

Push Button: Normally Open Momentary Switch with a Cushioned Contact (De Reamer, GE 1939)

A panel push button that closes a circuit only while you press it. A spring holds the button out, and a metal rim on the end of its rod sits clear of two contacts. Press it and the rim bridges both contacts. A second spring inside the button lets the rod give, so the contacts never take more than that spring's force. Source: Frank C. De Reamer, US 2,166,803 (General Electric, 1939), Fig. 5. Unknown: the insulating material, the metals and every size. De Reamer gives none of them, so they are linked to unknown heads. The tools are ours. Picture: the patent's Fig. 5.
Nâng cao
2 days

Hướng dẫn

1

Mould the housing

Mould a cup-shaped housing of insulating material, with a boss on each of two opposite sides, a recess in the top of each boss, a groove inside below each boss, and a bead round the top. Unknown: the material, the sizes and the moulding.

Vật liệu cho bước này:

Vật liệu cách điện chưa rõVật liệu cách điện chưa rõ1 as required

Công cụ cần thiết:

Khuôn ép nénKhuôn ép nén
Kích thước chưa rõKích thước chưa rõ
2

Make the terminals and contacts

Bend two angled metal strips. The upper end of each sits in a boss recess, and the lower end is a solder lug. Fix each upper end to a contact that fits the groove inside the housing, stepped at its bottom end. Unknown: the metal.

Vật liệu cho bước này:

Kim loại chưa rõKim loại chưa rõ1 as required

Công cụ cần thiết:

Kéo cắt tônKéo cắt tôn
Kìm mỏ dẹtKìm mỏ dẹt
Kích thước chưa rõKích thước chưa rõ
3

Make the sleeve, plate and cover

Turn a threaded sleeve and cut its thread. Spin its lower end over onto a metal plate with tangs. Cut a cover of insulating sheet with ears that reach over the bosses and a hole in the middle to guide the rod.

Vật liệu cho bước này:

Kim loại chưa rõKim loại chưa rõ1 as required
Vật liệu cách điện chưa rõVật liệu cách điện chưa rõ1 as required

Công cụ cần thiết:

Máy tiện kim loạiMáy tiện kim loại
Bộ dao tiện gỗ (HSS)Bộ dao tiện gỗ (HSS)
Tay quay bàn renTay quay bàn ren
Kéo cắt tônKéo cắt tôn
Thước cặpThước cặp
Kích thước chưa rõKích thước chưa rõ
4

Make the push button

Make a drawn metal tube closed at the top, and a rod with a head. Put a small coil spring in the top of the tube, then the rod's head. Wedge a washer into the tube under the head. Leave clearance so the rod can swivel a little. Turn the rod's lower end down to a smaller diameter. Unknown: the metal.

Vật liệu cho bước này:

Kim loại chưa rõKim loại chưa rõ1 as required
Bộ lò xo nénBộ lò xo nén1 spring

Công cụ cần thiết:

Máy tiện kim loạiMáy tiện kim loại
Bộ dao tiện gỗ (HSS)Bộ dao tiện gỗ (HSS)
Thước cặpThước cặp
Kích thước chưa rõKích thước chưa rõ
5

Assemble

Set the terminals in their recesses and the contacts in their grooves. Slide the button into the sleeve, with a coil spring round the rod between the cover and the wedged washer. Pass the rod's end through the cover's hole. Put on it a loose insulating washer with a metal rim round its edge. Hammer the rod's end over into a flange. Lay the cover on the housing, so its ears clamp the terminals, and bend the plate's tangs over the bead.

Vật liệu cho bước này:

Vật liệu cách điện chưa rõVật liệu cách điện chưa rõ1 as required
Kim loại chưa rõKim loại chưa rõ1 as required
Bộ lò xo nénBộ lò xo nén1 spring

Công cụ cần thiết:

Ê tô bàn nguộiÊ tô bàn nguội
Búa đầu trònBúa đầu tròn
Kìm mỏ dẹtKìm mỏ dẹt
Kính bảo hộKính bảo hộ
6

Mount and wire it

Put the sleeve through a hole in the panel and clamp the panel between two nuts on the thread. Solder the bared wire ends to the two lugs.

Vật liệu cho bước này:

Đai ốc lục giácĐai ốc lục giác2 pcs
Dây thiếc hànDây thiếc hàn1 as required

Công cụ cần thiết:

Mỏ hànMỏ hàn
Kìm mỏ dẹtKìm mỏ dẹt
7

Check it

At rest, the rim sits against the underside of the cover and the circuit is open. Pressed, the rim meets the stepped ends of both contacts and closes it. The checking is ours: the meter reads open, then closed while pressed.

Công cụ cần thiết:

Đồng hồ vạn năngĐồng hồ vạn năng

Vật liệu

5

Công cụ yêu cầu

13

Bản thiết kế này làm ra

CC0 Phạm vi công cộng

Bản thiết kế này được phát hành theo CC0. Bạn tự do sao chép, sửa đổi, phân phối và sử dụng cho bất kỳ mục đích nào mà không cần xin phép.

Hỗ trợ nhà sáng tạo bằng cách mua sản phẩm qua bản thiết kế, nơi họ nhận Hoa hồng nhà sáng tạo do nhà bán hàng đặt, hoặc tạo phiên bản mới và kết nối trong bản thiết kế riêng để chia sẻ doanh thu.

Thảo luận

(0)

Đăng nhập để tham gia thảo luận

Đang tải bình luận...