NGHỆ THUẬT
LÀM ĐẸP VÀ SỨC KHỎE
THỦ CÔNG
VĂN HÓA VÀ LỊCH SỬ
GIẢI TRÍ
MÔI TRƯỜNG
THỰC PHẨM VÀ ĐỒ UỐNG
KỸ THUẬT NGƯỢC
KHOA HỌC
THỂ THAO
CÔNG NGHỆ
THIẾT BỊ ĐEO
Steel Needle: Pointed, Eyed, Hardened in Oil and Tempered
Forge

Tạo bởi

Forge

18. tháng Mười 2026NO
20
0
0
0
0

Steel Needle: Pointed, Eyed, Hardened in Oil and Tempered

Needles are made from good steel wire: cut, straightened, pointed, flattened and pierced for the eye, hardened by heating and plunging into oil, then tempered back to a springy hardness, scoured and polished (Bucknall Smith, A Treatise upon Wire, 1891). This is the same sequence by hand, one heavy needle at a time from piano wire; the hand methods and sizes are ours. The picture: steel sewing needles (Wikimedia Commons).
Trung cấp
Half a day

Hướng dẫn

1

Cut, soften and straighten

Cut 70 mm of 1.2 mm piano wire. Heat it to red in the forge and let it cool slowly in the ashes so it can be filed and drilled, then roll it straight on the anvil.

Vật liệu cho bước này:

Dây đàn pianoDây đàn piano70 mm

Công cụ cần thiết:

Kìm cắtKìm cắt
Lò rèn của thợ rènLò rèn của thợ rèn
Kìm mỏ nhọnKìm mỏ nhọn
ĐeĐe
2

Point

Clamp it in the vise and file a long, even taper to a sharp point, turning the wire as you go.

Công cụ cần thiết:

Bộ giũaBộ giũa
Ê tô bàn nguộiÊ tô bàn nguội
Kính bảo hộKính bảo hộ
3

Flatten and pierce the eye

Flatten the head end slightly on the anvil, drill the eye through the flat with the finest bit, then file off the burrs and round the head.

Công cụ cần thiết:

ĐeĐe
Búa đầu nêm ngangBúa đầu nêm ngang
Khoan tayKhoan tay
Bộ giũaBộ giũa
Ê tô bàn nguộiÊ tô bàn nguội
Kính bảo hộKính bảo hộ
4

Harden in oil

Heat the needle evenly to red and plunge it into the oil. It is now glass-hard and brittle.

Công cụ cần thiết:

Lò rèn của thợ rènLò rèn của thợ rèn
Kìm mỏ nhọnKìm mỏ nhọn
Bể tôi dầuBể tôi dầu
Kính bảo hộKính bảo hộ
5

Temper

Reheat it in the oven to about 600 °F (315 °C) and let it cool slowly to a springy temper. If it came out crooked, straighten it with light blows of a small hammer on the anvil.

Công cụ cần thiết:

Lò nhiệt luyệnLò nhiệt luyện
Cặp nhiệt điện có đồng hồ hiển thịCặp nhiệt điện có đồng hồ hiển thị
ĐeĐe
Búa đầu nêm ngangBúa đầu nêm ngang
6

Scour and polish

Scour it bright with emery cloth, a little oil and soap. Wash it in hot water, dry it in sawdust, touch up the point, and polish it on the leather strop.

Công cụ cần thiết:

Vải nhám emeriVải nhám emeri
Dầu ô liuDầu ô liu
Xà phòngXà phòng
Mùn cưaMùn cưa
Dây da liếc daoDây da liếc dao
Bộ giũaBộ giũa

Vật liệu

1

Công cụ yêu cầu

17

Bản thiết kế này làm ra

CC0 Phạm vi công cộng

Bản thiết kế này được phát hành theo CC0. Bạn tự do sao chép, sửa đổi, phân phối và sử dụng cho bất kỳ mục đích nào mà không cần xin phép.

Hỗ trợ nhà sáng tạo bằng cách mua sản phẩm qua bản thiết kế, nơi họ nhận Hoa hồng nhà sáng tạo do nhà bán hàng đặt, hoặc tạo phiên bản mới và kết nối trong bản thiết kế riêng để chia sẻ doanh thu.

Thảo luận

(0)

Đăng nhập để tham gia thảo luận

Đang tải bình luận...